Hello all,
in my previous question (Switch between applications (multiple services.h)) I got the advice to merge my two services into one service, including a HID over...
I am trying to create an nRF8001 based application that will broadcast battery levels (pipes broadcast, set), and give out temperature data (pipe indicate - TX_ACK) to connected...
Hi,
I'm using redbearlab's nrf51822 board. It is a arduino compatible board and hence it is using 0,1 (mapped to 9 and 11 for nrf51822). How do I make printf print to this...
An external PA/LNA is used to extend range of nRF51822, and S110 is used for BLE, How to switch between PA and LNA? and how to disable PA/LNA when there isn't transceiving...
Hi...
Can anybody help me to run ble_peripheral example (ble_app_hrs for S130). I have build and load the code successfully but cant see the advertisement. But while debugging...
I am working with the nRF8001, and I'd like to create a services.h file that will let me broadcast battery level and as well as allow temperature to be read by a peer.
...
Hi We have an application where we what to read i2c sensor data over the air to an iPhone. We've taken ble_app_uart_S130 project and grafted in some twi_hardware code. There...
Hello Nordic,
I recently setup the Command Line application for our device, using USB CDC ACM. I started experimenting in the example cli project. After everything was...
Using nRF Connect SDK v1.2.0 on nRF52840 DK (PCA10056)
We are evaluating the nRF Connect SDK on the 52840 until our 5340 PDK arrives. While running the mesh light example...
Hi and nice to meet you,
I freshly get my nrf52833 DK. I'm working on windows. I have installed via nRF Desktop all necessary tools.
We are moving our project from nxp...
Hello,
I am trying to connect NRF52832 with another Bluetooth module using custom characteristics. I was able to connect two NRF52832 modules but I can't connect to another...
Hi,
After updating NCS folder to latest Master branch, SES4.52 is not able enter into debug mode.
Receiving error as: failed to set startup compilation break point:...
I have a bootloader, softdevice and firmware (all with sdk 15.0 and softdevice V. 6) on a nrf 52840 on an counter-pcb.
I have upgraded the firmware to sdk 16.1 and use the...
Hello together, I am just starting to work with the nRF9160 and have some problems with the configuration. I inserted the iBasis SIM card and tried to get a LTE connection...
Hi,
I am using a ble_app_blinky example (SDK16) to communicate with the BLE devices. NRF52840 is connected with the client devices and successfully sending the data to the...
Hello,
I would like to know if it is possible to not use softdevice because i need more flash for my code. I guess it is possible but when i don't enable softdevice in my...
Hello,
i'm trying to use SPI with nrf9160DK as master and RFM96 module as slave. At the moment, i'm developing elementary functions to write and read from my slave device...
Hello
I am working on Nordic nrf52832
I am using the "ble_app_blinky_c_pca10040_s132"
I want to use ble for scanning a beacon (eddystone TLM) and collect its data. ...
please help. I need functional description of what is need step by step for doing a zigbee hardware device switch and management over bluetooth on the thingy52, i have all...
Hi Team,
We are using the NRF52840 with s140 Soft device for our BLE application.
While we are facing some issues while doing debugging.
1. We are getting Hard Fault...
Are there any issues of pairing a nRF52833 using OOB pairing with a IOS device? Is there a good example code I could start with?
Thank you very much.
All the best
P...
The system requirements: 50 identical nRF53-based devices (each with a sensor and an actuator), positioned within a 3x3 meter square should be connected to a single computer...
