Hi,
I am using ADC without external reference and no analog input in order to measure the battery level with a timer (code at the end).
I am also reading several ports...
Hi,
I'm programming the nRF51822 and save some user data into the FLASH by using pstorage_update . It works fine if I set system off mode, and wake it up. I can read back...
Hi,
I have been using nRF51822 with my Android app using Android's Bluetooth Low-Energy APIs.
In order to get more details, I am currently working on integrating the Android...
I'm looking at interfacing a typical Wheatstone bridge sensor to the nRF51822 ADC. This particular sensor only requires a mA or two for excitation and the output fits within...
When use the "nRFBeacons" app to update the info on my beacon the following happens:
Go to update tab.
Select "Connect"
Press "SW2" on beacon and see the LED begin flashing...
I am using s110 and nrf51822. I've set up up a long characteristic of 154 bytes.
Sending between 1 and 154 bytes works as expected.
Sending 155 - 160 bytes gets rejected...
Hi,
I tested the nrf beacon application, it allows only the beacons with company identifier 0x0059 (nordic's id). But i need to modify it to support all the device, how...
Hi,
I need DFU feature on light_switch_dimming_client_nrf52832_xxAA_s132_7.0.1 example i tried including
mesh_stack_init_params_t init_params = { .core.irq_priority =...
Hello,
I have a project that seems to have a very long start-up/boot delay before jumping to the Application when the DFU is added. DFU is the BLE secure bootloader example...
Hi Nordic ,
I am working a project on nRF52830 with SDK 15.3. Now, I developmet on a central device, I need to connect with peropheral with more than one service , how...
Hi.
I'm using nRF52840 Developement Kit and my environment are below.
OS : windows 10
SDK version : 16.0.0
Tool : nRF Connect (with DTM,Programmer app) / Seger embedded...
Hello everybody,
I'm trying to flash an example code (let's say the blinky one) from the SDK (15.3) onto the Arduino Nano 33 BLE board.
I know that is possible to flash...
Hello,
I'm trying to resolve an issue in my project.
It appears there is a memory leak.
In logs I can find the error code : 0xBFED
Do you know what that code is? ...
Hi,
I recently had a problem about timestamp that it's all 0 on the RTT Viewer.
And i 'm based on the nRF5_SDK_15.2.0\examples\peripheral\rtc to check the timesteamp....
Hi Nordic
I have some issue When using NRF52832 central to connect the NRF52832 peripheral.
i am following the SDK15.3.0 ble_app_uart & ble_app_uart_c to deign the central...
Hi
I have a question about LXFO input on external low swing clock setting using nRF52832.
I can see the input specification of external low swing clock about only peak...
Hi,
I am currently developing a stationary BLE device. I am testing the nRF52840-dongle in combination with the pc-ble-driver. For that purpose, I am using the connectivity_4...
SDK: 15.3.0 Device: EYSHJNZWZ (nRF52832)
I am operating in a "peripheral" configuration, with bonding enabled. "BLE_GATTS_EVT_WRITE" occurs when notification is permitted...
We're porting over some software to the Arduino Nano 33 BLE Sense. This board comes with an nRF52840 clocked at a max. of 64MHz. However, the same code runs about 2x slower...
I want to send Tx power in advertisement packet.
Currently I am using following code.
int8_t txpower_level;
static ble_advertising_init_t init =
{
....
