When use the "nRFBeacons" app to update the info on my beacon the following happens:
Go to update tab.
Select "Connect"
Press "SW2" on beacon and see the LED begin flashing...
I am using s110 and nrf51822. I've set up up a long characteristic of 154 bytes.
Sending between 1 and 154 bytes works as expected.
Sending 155 - 160 bytes gets rejected...
Hi,
I tested the nrf beacon application, it allows only the beacons with company identifier 0x0059 (nordic's id). But i need to modify it to support all the device, how...
I use a app_timer_create() function to create a task(200ms once)
when in the task_timeout_handle() ,
I do something more than 200ms,
what will this timer going ?
Hi!
I use nrf51-pwm-library ( github.com/.../) to control brightness of LED RGB light source and it works ok till I don't want to adjust brightness slowly (dimming function...
hello,
are there any completed sample code of using pwm0, 1?
just 2 or 3 word can working like following? or need other config?
pwmcon=xx;
pwmdc0=xx;
pwmdc1=xx;
also...
I am planning to migrate to SD 7.0 and SDK 6.0 in order to use the static pass key capabilities. When using the static pass key how should security params be initialized ...
Hi, I'm working with nRF52840 with NFC. I don't have yet the external antenna to connect to (now I'm using uFL), but I'm not sure about the trace width that goes from the...
MeshSDK: 3.2.0
StockSDK: 15.2
Hello,
I have a network where the sequence numbers have become corrupt due to removing devices from a network and then provisioning other...
Hello,
I've been trying to write my own library that uses UART.
I went through the "uart" example and wrote this piece of code.
uart.c
gpio.c
main.c
...
I would like to ask you a question, that is, the RTC in the chip of 52832, in the case of non-power-off restart, is there any way to keep the RTC time and continue the timing...
I am trying to extract the gps coordinates and use CoAP to sent the info to Telenor IoT server. I am using the gps demo code provided by Nordic .
https://github.com/NordicPlayground...
Hello,
I want to program nRF5340 via UART.
What is the hardware related event that puts the application processor in program mode over the UART ?
All ARM microprocessors...
Hi
OS: Windows 10 (32-bit)
nRF Connect application: v3.3.1
Getting started assistant: v3.3.1
Please see the attachment. After installing ninja, tried to verify it...
I`m searching after an application document / description of a test setup, how to measure BLE data throughput with our product including nRF52840. Maybe Nordic have a smart...
I've been programming in SES for several months now, and I need to put the code into libraries to keep an overview of my project.
I've been able to include SDK libraries...
hi, I used NRF52833 to debug the program, and I used the ble_app_hid_mouse project in SDK16 to debug the fstore function ,and the file path is E:\nrf52833\nRF5SDK160098a08e2...
Hi everyone,
This is my first time using Nordic nRF SDK, so i hope that I'm not asking for anything too stupid, I'm having troubles in adding nrf_logger.h into a project...
I've noticed that the BT-SIG listings for s132 v6.1.x https://launchstudio.bluetooth.com/ListingDetails/64933
and s140 v6.1.x https://launchstudio.bluetooth.com/ListingDetails...
Hello everyone!
We are developing a device with the nRF52840 SoC and using mbed-os for developing firmware.
Everything works and runs normally when using mbed softdevice...
51822+LIS3DH
I have tested my board and got the current consumption value. I use slow advertising only and the interval is 2 seconds. Follow is the result:
1. advertising...
