Hi Hakon.... when i compile my project i get some linker errors,
._build\gzll_host_ack_payload.axf: Error: L6218E: Undefined symbol __main (referred from arm_startup_nrf51...
I'm trying to perform communication between my device and iOS and I ran into some problems. For tests I'm using iPod touch 5 with nRF Toolbox and LightBlue apps and nRF51822...
I've been using Master Emulator API 2.1.3 in Visual Studio 2010 Express, and have spotted a fix I may need in 2.1.5 so I've switched to using the 2.1.7 API. However, I've...
Hello,In normal condition, I use UART,pwm,spi an so on.Now I want to clear the configuration, and enter System ON mode.But I don't want to system reset.
How should I do...
Hi, everyone~
My goal is to collect data from 4 sensors simultaneously using iPhone.
Now, my testing code for sensor nodes is working fine. It was built based on the...
I am an android developer and I am using your nRF Master Control Panel (BLE) product as published on Google play. Below is the link to the app:
play.google.com/.../details...
I want to build a USB dongle, so I purchased the nrf24lu1+ development kit. However, in order to program the target board, it would seem that I need the nrfgo. Is this correct...
Hello Nordic
I am working with nrf52832, sdk 16.0, softdevice s132
I need to advertise NON CONNECTABLE ble with changeable data (later relevant data will be received...
Hi
we are using the nRF52840 and antenna signal i connected ceramic chip antenna(ACAG020-2450-T).
The above attached schematic of ant signal matching circuit schematic...
The only way I can see to do it is by two separate PPI calls. So Timer1 "tasker" is firing both the capture and clear... but will they execute sequentially?
Hi,
I just bought the NRF52850 DK. Currently I do not have the JLink connector to perform debugging using UART.
Is there is a way I can print printf or NRF LOG through...
Hello expert,
I would like to design a custom PCB that has two transceivers on it. One transceiver is working as a beacon/continuous wave generator (TX) and the other one...
On the basis of NRF24L01 +, an antenna was designed. after designing, I need to carry out the coordination of circuits. Do not tell me how best to do this, what values to...
I had a setup where I could DFU OTA a NRF52832 based board
I moved to a NRF52840 based board and now during the OTA DFU I get messages like this
I did try a new bootloader...
Hello, guys.
We have nRF9160DK and nRF Connect SDK v1.3.0. The version of the LTE modem firmware is the latest (v.1.2.0).
In our design, we are able to initially connect...
Hi Nordic team,
I just purchased a row of new nrf9160 SiPs for our IoT products. We are testing with new made cuicuits.
We use the same circuit schematic that worked with...
Hello,
Problem: BLE doesn't work on a OurBoard with nRF52840 (Schema1).
1) BLE example is working DevBoard (can see BLE server by scanner). On the OurBoard the examle...
Hello,
I've been testing HCI_UART from Zephyr RTOS on nRF52840DK and own device which has nRF52840 + FT232R as USB-UART converter. Regarding the own device it's a circuit...
I am studying the beacon example provided in the SDK (The project is found in following directory C:\Nordic_semi\nRF5SDK160098a08e2\examples\ble_peripheral\ble_app_beacon...
Hello there, I'm developing a device who will use two NRF52832(ANNA-B112 Module). They will communicate as central and peripheral. But i'm facing a problem, i need to after...
I could decrease current consumption at v1.2.0, but couldn't at 1.3.0. 520uA flows in k_cpu_idle();
How can you do that?
Also, in v1.3.0, CONFIG_UART_0_NRF_UARTE is depricated...
