I'm interested in creating a time of flight algorithm and am trying to calculate what to expect for accuracy.
Is it possible to get an IRQ from when the sync arrives at...
hi all ,
how to enable GPIOTE PORT and IN[n] event simultaneously ?(not same pin)
i enable the GPIOTE to trigger interrupt event.
one for the keyboard which need multiple...
Hi All,
I am using nRF51422 with softdevice s310. And implementing Cycle speed and cadence receiver. most of the data processing is fine but i am facing one problem.
...
Hello Nordic Team,
I have a problem with programming the nRF24LE1 chip.
I am developing a small system, which consists of a uC STM32F4xx and a nRF24LE1 Radio Module. The...
Hi,
I'd like to learn about the app compatibility for the new OTA DFU that ships with the new SDK 6.0.0 and S110 7.0.0. I am using a nRF51822 board and I've observed that...
I'm curious to know if there is a tool that allows easy design of a GATT server DB that is portable across dev platforms (the nrf518 EK, my Android/iOS dev environment etc...
Iam trying to display the uart data as a scanned response.nRF51822 receives the data from PIC and it is displayed as scanned response during advertising.the problem is nrf51822...
I really don't understand your terminologies. In beacon example you are passing BLE_GAP_ADV_TYPE_NONCONNECTABLE_NONSCANNABLE_UNDIRECTED. It is getting scanned in NRF CONNECT...
Hi,
Trying to implement ECDH I struggled creating the random seed. Using Nordic Security Backend and Vanilla Mbedtls on the nRF5340 I get the following errors:
Minimal...
Hi,
I am developing the board to act as Broadcaster and also Observer
I am using SDK_16 with SEGGER EMBEDDED . nRF52
board wants to do Broadcast the signal ( non-connectable...
Figure 7 of the nRF24L01 data says ACK payloads must be loaded in advance to the automatic ACK transmission. I wish to make the ACK data packet dependent on what is received...
Hi：
I noticed, P0.18 P0.19 P0.21 P0.22 P0.23 P1.00，recommended as QSPI.
There is no way to raise the P0.22 pin using this code.
But my own board must use P0.22 as...
I'm been analyzing this code for a while now but can't see how this code actually triggers a switch into the Bootloader mode. There are no references to any resets or the...
Hello
I would like use at least 2PPI channels to control a GPIO.
If PPI CH0&CH1 both setup, then GPIO_CTL just go high.
If PPI CH0 remarked, then GPIO_CTL go low
How...
Hi, 1. What document can guide the macro definition of configuring the nrf9160 project? 2. How do you know that prj.conf has those macro definitions how to configure? 3. A...
Whose idea was it to make creating a new project from scratch so difficult (if not impossible)????
I have created numerous projects using the nRF5x, but have always used...
hello,
I am using SDK16 ble_app_gls example . I set static passkey with adding this code in ble_stack_init function.
When I write password "123456" I can connect on nrf...
Hi
This question is related to sd_ble_gap_keypress_notify() . According to Nordic softdevice S132 v3.0.0 API:-
"This function can only be used when an authentication...
Hi
I am currently working on calculating the AoA. I have 4 nRF52833 DKs and I am using three DKs as transmitters and one as the receiver and the receiver is connected to...
This page https://www.nordicsemi.com/Software-and-Tools/Development-Kits/nRF52840-DK/GetStarted says " If step 4) below fails, you need to re-program the factory example code...
How can I calculate max and average power of this chip? During use, I intend to be at 0dB TX and 1 Mbs data rate with a 3V supply. I am going to guess the max power draw will...
Hello everyone
I am using nRF52 DK PCA10040.
I try to generate puls by Timer 0.
The puls width is 400ns.
This goal was failed.
---------------------------------...
