Hello,I am working with the nRF9151 SMA DK and I need the VDD_GPIO rail to operate at 3.3V to interface with some external components.
According to the schematics, VOUT1...
Hi,
I want to download FOTA-updates with HTTPS from a function app running on Azure. I am not using IoT hub or MQTT. I'm using modem firmware 2.0.4 in combination with version...
Hi,
In our PCB using the nRF54L15, we used different P2 pins for the sQSPI, believing after reading the docs and driver API, that one could configure different pins than...
Hi, While using the Axon TFLite compiler to compile a series of TFLite models, we encountered a peculiar issue. The largest layer in the models (i.e. the dense layer right...
Is it necessary to perform the GATT device discovery process whenever two bonded device re-connect? I'm using two nRF54L15-DK boards, one is Central and one peripheral. Developing...
While configuring a scene, the blind device is not visible in the scene settings screen, so it is not possible to set or save the blind position as part of the scene.
Steps...
Hello.
I need to use LESC numeric comparison pairing.
It seems that the PIN is automatically and ramdomly generated after the connection occurs.
I would need to manage...
I am running a nrf52 with IOT sdk's Cloud CoAP example. I am wondering about the parameters that I would need to integrate this into a product. These include the stack size...
Hello,
I am using 52832 to test ble data throughput. When two devices are close to each other, the throughput can reach 80kB/s, but if the distance is about 4 meters, the...
The nRF51422 product specification says that you have to use a +-40 ppm crystal for BLE applications.
On DigiKey, there are 2 columns for 2520 crystals: frequency stability...
Hey,
I just want to know if anybody sucessfully connected HDMI CEC (One-Wire bus) with the nRF52832.
I would be very grateful if anybody could share the library or give...
Hello, I downloaded the ble_mesh_v0.9.1-Alpha source code from nordic website, and tried to port it to my pca10056 devboard.
When doing so, I noticed that some function...
Hi All,
I would like to use FreeRTOS in my project. I try to play with the examples/ble_peripheral/ble_app_hrs_freertos project.
I have enabled logging with RTT. The...
Hi, when reading BLE Mesh specs, this paragraph caught my attention:
Messages may support a delay parameter that indicates a delay between receiving a message and
starting...
nRF5 SDK v13.0.0
Release Date: Week 11, 2017
Highlights:
Implemented a new license scheme for the SDK distribution. See the
documentation folder for details....
Hi,
I am using "nrf5 sdk v11.0" ble_peripheral "ble_ancs_c" example for nrf52_DK(PCA10040) .
When i connect to the my ios device then accepted pairing request then i am...
is it possible configure the QDEC to single phase, i am using one omnipolar hall effect sensor i am wondering if i can configure only phase A ande use it, is it possible ...
Hi, I wonder why my pwm uses so much power in WFI mode. It uses around 470uA and when I do not use pwm that current is around 1.8uA. I tried to disable pwm but without success...
if i am not wrong the connections i found is as i shown in the image..
the module doesn't show up in my ide tool (keil ) although my kit works fine but i need it for standalone...
Dear Nordic Team,
I am work DFU with ble_app_uart example , as per the info center document : infocenter.nordicsemi.com/index.jsp and also followed by the example for ble_app_hrs...
when use the sd_ble_gatts_hvx() send data and printf() the value below
p_ble_evt->evt.gatts_evt.params.hvc.handle
p_ble_evt->evt.gatts_evt.params.sys_attr_missing.hint...
