Hi,
We are developing an application that requires synchronization between two or more nRF9160-based devices. We have the following requirements and constraints:
Required...
I'm using the prebuilt Aliro stack (libaliro.a, nRF52840), when a session fails inside the library we have no way to get the resulting AliroErrorCode. The stack entry points...
Hi,
We have deployed some devices now, and we see quite some modem faults popping up.
Could you try to give all info on what you know about these faults we have from...
Environment
SoC: nRF54LM20 (DK; silicon reports nRF54LM20B ENGB — also reproduces built for the LM20A target)
nRF Connect SDK: v3.3.0-rc2, west v1.5.0
Bluetooth: SoftDevice...
Hello
We are using nRF5340 as our EVK with a 12 antenna array plate(4x4 with center 4 ones not being there). Our beacon uses nRF52833.
We used Nordic's sample codes- ...
Title: nRF52840 / OpenThread: how to inject custom IEEE 802.15.4 RX frames into the native receive path?
Hi,
I am working on a test setup around nRF52840, OpenThread,...
Dear Sir,
Here I test the ble_peripheral example "ble_app_uart" (Softdevice 8.0) with Kail MDK ARM 5.20 environemt on the PAC10028A board.
I found it's not stable and...
Hi,
I'm having trouble increasing frequency of data TX using ble_app_hrs example on PCA10028.
I tried to increase the TX frequency of heartrate data to 100ms by configuring...
It seems that the nRF52 Development Kit mis-handles extended hex records. If it has type "04" records (extended linear address), it works OK, but if it has type "02" records...
We have an optical measurement system where we need to pulse LED and sample a phototransistor precisely during the LED pulse. The rate of sampling is 1 kHz and we plan to...
HI i need help in sending a data value of 700+ continuously
1)May i know how should i format my data packet to suit the current 20 bytes of data sent through BLE
2)Is...
Hi,
I am working on application in which I want to send 1000 or more samples using SAADC and BLE over standard master control panel APP of Nordic. For sampling analog data...
I'm trying to fully understand how DFU works and am going through the nRF5 SDK v11.0.0 example bootloader ( dfu_dual_bank_ble_s132_pca10040 ) and app ( ble_app_hrs_s132_with_dfu_pca10040...
[summary]
When I update app by Keil μVision, RAM setting is reflected correctly, but when I update app on OTA, RAM setting change is not reflected.
[condition]
Old...
Im trying to read flash memory ( N25Q032 ) identifier using SPI (NRF52) but then eveytime I try to read a register, the output is always zero, I tested with oscilloscope and...
Hi,
I'm using the nRF Dongle for sniffing.
Apparently there are many problems with the sniffer application.
First of all, the CTRL+R command for downloading the FW...
Hi!
I am trying to modify the ble_app_gls example from the 8.0.0 SDK and am running into some issues. I am trying to add the nus service to this example and would like...
HI dear:
We have two questions to ask you：
1、Can we customize two different BASE_UUID in the nrf52832 ? If we can,and how to do it,We can customize one BASE_UUID (128bit...
Hi there,
I'm new to the nRF52 and to ANT, so I'm in the process of running through some of the example code. I've been able to successfully run peripheral and BLE examples...
Hello,
i'm looking for the NRF52832 QFN48 6x6 symbol and footprint in Orcad/Allegro format to accelerate my design,
unfortunately, my electronic designer don't use Altium...
