I am trying to measure the 300mA system current.
I cut off the system lane and connected Vin, Vout.
And when in ampere mode, the system is not turning ON.
(When I replaced...
Hi Nordic,
I have a custom board using a Raytac MDBT53 module with nRF5340. The board is designed for 3.3 V / LDO mode, but during bring-up I likely flashed firmware/configuration...
Hello Nordic support,
I am using two nRF54L15 devices with NCS v3.0.1 and ESB DPL at 1 Mbps. Auto ACK is enabled, the payload is 252 bytes, and the retransmit count is 9...
# SoftDevice Controller assert during DTM receiver test at dead/marginal RF link (nRF52833) ## Summary On an nRF52833, running the nRF Connect SDK Direct Test Mode (DTM) 2...
A customer implemented a nRF52840 (QIAA package) and says the output power is about 10dB lower than expected. Having done multiple nRF52 designs with good results, I reviewed...
While configuring a scene, the blind device is not visible in the scene settings screen, so it is not possible to set or save the blind position as part of the scene.
Steps...
Hi, when I run the ble_app_proximity on my 51822 board, I can connect the 51822 board with NRF Master Control APP, after a little while , 51822 disconnect with app, and trace...
Hi.
Is this issue resolved?
github.com/.../902
I tried lately using mbed-rtos with nrf51822, but no luck.
I would like to use threads, is there a way to circumvent...
Hello everyone,
i'm kinda new to microcontroller programming and feel like i bit of more than i can chew. I bought a variant of the nrf51822 chip ( github.com/.../Board...
Hi. Currently, i am testing the BLE power consumption on nrf52.I set connection interval 20ms(min=10,max=30) ,slave latency 0 and connection data size 20 bytes.in addition...
It seems like the IAR startup file in SDK 11 for nrf52 is older than the one that was included in the previous SDK 11 alpha
IAR Embedded workbench 7.50.3
I have a queston for softdevice S130 example about Environmental Sensing service.
I readed spec. but I can't find out any ESS profile example in SDK.
Is SoftDevice S130...
I want to use the nRF24LU1+ for a project where it will be a HID usb dongle. But I dont get which tools I need to make it. The KIT DEVELOPMENT NRF24LU1+ work for it?
T...
Hello,
This morning i did migration of my code from SDK 11 alpha 2 to 11 final on nRF52 and i have a big problem.
Nor bootloader or application do advertising. Am I...
I want to merge the softdevice and application in the makefile is it possible ?
if not possible what could be the easier way. I am using Linux OS .
thanks
Hi everyone.
I'm trying to program a NRF51822 Beacon using the nRF DK board. Of course I looked around here for advice on what type of connector to obtain.
devzone.nordicsemi...
Hi,
I have a hardware (wired) UART transmitting data to the nRF51 at intervals. I'm currently trying to implement UART-BLE that runs could concurrently with the wired UART...
is there a version of nrfutil that works on linux?
this one doesn't: github.com/.../pc-nrfutil
$ nrfutil dfu genpkg --application _build/nrf51822_xxac_s110.hex fota.zip...
Hello,
I have used ble_app_uart example and wants to transmit 12 bytes data over ble using this function ble_nus_string_send call.
In 1 second how many times ble_nus_string_send...
