I'm trying to use the ADC and internal reference to measure battery voltage on the nrf51422, while S210 is enabled.
From the example nrf51-ble-app-temp-master, I found...
I have Nokia Lumia 630 and it works well with nRF51822-EK but only with SDK nrf51822_v5.1.0.36092 and SoftDevice 6.0.0. Now I decided to try DFU OTA. I programmed bootloader...
Hello,
I found that there is a multiprotocol demo in folder Board\nrf6310\s110\experimental\ble_app_multiactivity_beacon,then I found it can implement concurrent connected...
Dear Sir
We got the problem on DFU upload firmware, it always failed in second DFU . We must unpair the device at iOS setting panel. Before next DFU.
Here is the log data...
Hi All,
My requirement is to read the data from nRF51822 device that is connected to a bluetooth and bluetooth is connected to a system using a .Net application.
I have...
Hi everyone,
I'm using the nRF51822 (pca10000 Dongle + pca10005).
My plan is to send one byte over the radio.
I tried to use the SDK-Example as a template but it's...
Hi,
Is that possible to run the radio_test_example (\nRF51 SDK_v5.2.0.39364\Nordic\nrf51822\Board\nrf6310\radio_test_example) on the nRF51822EK? If yes, what modifications...
Hi there,
I see the "Error 133 (0x85): GATT ERROR" in the nrfconnect App with an HTC U11 Life with up to date Android (8.0.0).
I tested the nordic ble_app_uart example...
I am setting up the Power Profiler kit as standalone, no DK, measuring external target, also use the Segger jLink as interface. With the 2.0 software, it could not connect...
hello ,
can anyone guide how to add custom service and charactericteristic and receive data from nrf connect app using handler
i am using
board :PCA10040
nRF52DK ...
Hello guys!
We have a new project were will have to use dfu ota for a custom made application on a nrf51 beacon. Since the beacons use legacy dfu we want a way around...
Hello! I am trying to advertise two 16-bit uuid's and a 128-bit uuid. I set up advertising_init as such:
I declared the following structures:
where "SENS_UUID_SERVICE...
I am using Fanstel BT832 module based on nRF52832. I am using ' nRF5_SDK_14.2.0_17b948a ' with ' s132_nrf52_5.1.0_softdevice.hex '.
I am using this module as the BLE peripheral...
Hey Dear Nordic Devzone,
Here I am again, it has been a long time. Before I was working with the nRF52840 and Segger Embedded Studio. But as of now the company I am working...
i have programmed a arduino to send data(int value) on tx ,rx pin .How shoul i set up the nrf52 (the pin no of rxd and txd on nrf are p0.6 and p0.8).Which example should i...
Hi,
I'm looking into the reliability of the BLE connection from one nrf52 to another nrf52. I'm looking to understand a few things.
Once a connection is established...
In both the SDK and production specification (PS 1.4) it is noted that the TIMER (Timer / counter) peripheral in 'COUNTER' mode (0x01) is deprecated.
For implementing a...
In my current case there is a relay node to which want to send RSSI values of beacons nearby and then relay the same information across other relay nodes in the network, So...
what is the problem of "ERROR Failed to open nrfjprog: Error occured when open device long term. Errorcode: CouldNotLoadDLL (0x3)" , when i use the nRF Connect.
the version...
