Hi, I have both the nRF8001 dev kit and the nRF51822 Eval Kit (EK). We are using the nRF8001 for most of our project with the BLE Arduino SDK. But I wanted to just load a...
Hi,
What is the suggested method to change a pending request, and make it earlier than previously requested, without closing and reopening the session?
For example,...
Hi,
I am using a custom pcb with a nRF51422 chip, and trying to setup ANT communication between 2 modules, but the sd_ant_channel_id_set call returns an invalid address...
Hi,
To use bidirectional continuous scanning mode in ANT, I have to transmit Extended Broadcast/Acknowledged/Burst messages using ANT Msgs 0x5D, 0x5E, and 0x5F (ANT Message...
We are preparing to get BT qualification for our product, developed with the 6 stack now, however want to update to 7 when it is finally released. A comment from the testing...
What is the best way to minimize transfer in progress errors when trying to send ANT messages? I am using the S310 stack on an nRF51422. I have a busy ANT channel that is...
I'm running into a weird timing issue with a nRF24L01+ which I'm not quite sure how to work around in the general case. The basic setup is two radios, A and B. Auto acknowledgement...
Hi,
I want to interface FN-M16P with nRF52 through UART. To access this module I need to send commands to perform specific actions.Is there any specific example like this...
Hello,
I am new in this community and I am trying to get started with developments using nRF52840 DK. I am using SDK 13.0 for the library and I compile my code using armgcc...
I would like to be able to leave the bootloader installed and debug an application. I have been able to use the merge tools to get the hex files all merged and generate the...
Hi, i'm currently working on a low power sensor device based on nrf52832. I want to transfer data only to bonded central devices. Priority is using static passkey, but my...
After reading a few related questions and the official tutorial, I have a guess, hoping to confirm:
If I do not need to add extra events into schedular for management purposes...
I'm doing experiments on high throughput and need to call sd_ble_gatts_hvx, but there are a lot of confusing things so it's hard to get started.
If I want to know if notify...
Hi,
I have a nRF24LE1 development kit and a starter kit. If I turn the power off and turn the power back on using the power switch S9 on the motherboard. The nRF24LE1 chip...
I am using pc-ble-driver-py to configure an nRF52832 demo board as a BLE central device. I currently have the heart_rate_collector.py example working. However, what I would...
I am build a sound client project
when I received the data from the thingy52（which is sound server device）
the I play the sound by function drv_speaker_ble_pcm_play...
Hello,
I'm trying to interface this cheap OLED display from ebay
and while running and debugging the code I think should work(all based off the TWI_sensor sdk example...
Hello All,
I am working on Raytac module based on nrf51822 with ble_app_uart code. I can see on module there is no external crystal ,
my module is not able advertise,...
dear nordic employee
I have two thingy，one of witch is the sound server（nordic provide）
now ，I want to do a sound client，I have learned the service knowledge
but...
Hi there,
I'm currently porting the nRFgo gzll_host_w_dyn_pairing_example however my microcontroller does not have an aes encryption peripheral.
It seemed easy to just...
Hello Dev Zone,
We've been using the IoT SDK 0.9 all year and recently ported to the production release bundled with the SDK 14.1 package.
We have the DFU working with...
Hi,
I am using SDK14.1 with nrf52832 and want to write to eeprom memory over SPI from BLE characteristic call.
My spi module works and everything was working fine until...
