Hi,
how long does it take time if i would wake up a nrf51422 rev2 (ANT and BLE) in deepest possible sleep mode ?
And how long does it tai if after wakeup it had to communicate...
I saw that the app_timer uses the SWI0. Could you explain what it does and what the advantage is compared to "timer_list_handler_sched()" calling "timer_list_handler()" directly...
Hi, I used the sample code "Master Emulator->2.1.7.8226->Example code->nRFUart"
to develop a new project, and encounter some questions...
we update nRF6310...
Hello,
How many RX buffers are in S110 SoftDevice? I know there are 6 TX buffers (so you can send 6 packets per Connection Interval).
How is it on receiving?
Is it e...
My sensor is off-standard,so I have to use gpio to read and write my sensor.
Gpio IIC will take about 0.5ms to get data.
My app need send data every 7.5ms,it seems that...
Hi,
My android Proximity application fails on service discovery only for the very first time it connects with the devices(nrf51822 evaluation kit with sdk 5.2.0). Actually...
Has anyone converted the app note AN34 DTM Python script to C# or C/C++ ?
The Python DTM script is works OK with the setup specified in the app note AN34 figure 2, which...
Dear Nordic engineer,
I try to setup Wireshark sniffer with nRF52-DK. I followed by nRF sniffer user guide v2.0.
I see interface toolbar of nRF sniffer on Wireshark. But...
Is there a block header information available that I can read thru the flash read function (e.g. in ble_flash driver, ble_flash_page_read() function ) ?
My FS (file system...
Hello,
I would like to understand the reason behind getting a error,(0x04) NRF_ERROR_NO_MEM , when calling the function
sd_ble_gatts_characteristic_add(p_service->service_handle...
I'am realy new to nRF52 development. I want to start with a simple demo as shown on www.nordicsemi.com/.../Getting-started-with-the-nRF52-Development-Kit.
What HW do I...
Every time I change a common source file within Kiel, the source file is changed for every project because (obviously) is a file common to all example projects.
Is there...
Is there a nordic guide which lists out the steps taken by the chip when going though a bonding process? I am trying to add as many RTT printouts as possible to know where...
finally I have done to implement that ADXL345 can throw data over BLE using nRF UART app service with this code . now my problem is how to change 2's complement ADXL345 data...
Hi,
We are using a nrf52832 in a serialized application with a STM32F4 and standard SPI as the transport layer. We are using the SDK V12 on the STM32 and softdevice S132...
Hello,
I want to add DFU fonction on my custom application. The final goal is to update my firmware from my custom app (not just once).
My setup is : SDK11 - nRF52832...
Hello All,
I am using the HRS example as reference from Nordic SDK14.1.
I have one central and 4 peripheral devices.
I have the MAC ID's for all the four peripherals...
Hello Nordic Experts,
I have One central device and and 4 peripheral devices.
At this point of time I am trying HRS example on it, the example is running fine with single...
Hi everyone,
We are trying to choose which protocol use for connecting devices based on Nordic SoCs.
We use devices in following way:
about 300 - 500 devices (wearable...
Hi there,
The dfu secure bootloader example is working fine with my nrf52832 sdk14.2 s132. but the experimental buttonless dfu in the example is not working for me. I was...
Hello,
I have nrf51 beacon that is protected from read. I want to recover it (erase and disable protection) but I only have st-link programmer. How can I do that? Maybe...
Hi,
I have been developing with nRF51 for some time and already implemented a nice 13.56MHz wireless charging circuit. Now that I'm moving to nRF52 I would like to keep...
