Hi.
I wonder if you could help me:
I'm using a thingy91x and would like to work with the npm1300. In the case of this hardware, the PMIC npm1300's i2c bus is connected...
RTT log output issue
Hello, I am using SDK v3.0.2 and toolchain v3.0.2. After building and flashing my firmware, no logs are being output to RTT Viewer. What should I do...
We tested the USB performance on the v3.1.0-preview4 and main it looks like it got even worse.
All tests were done on the attached test project: TestProject
main (6855b38ca69d2a70d0a088d9964e606e9981cb14...
Hi all!
I have the NRF54H20 D and somehow the RTT viewer doesn’t work, the board doesn’t work. I am using the most simple zephyr hello world project. It says it is compatible...
Hi there,
We are using for BLE communication a nRF52832 chip with random static address configuration (shown in the UART). Can we be sure that the address of a chip will...
I am building an application for the nRF52840 on Linux just using west . I have been struggling with this issue for some time now. The linker can't find any mbedtls_ccm functions...
Hello, I am experiencing issues with the current measurements taken by the PPK2 when using the nPM2100-EK to power a device. The current drawn from the 2.7V power source ...
Hi,
How can I understand what all Errata's are applicable to softdevice and are taken care of?
For my application I am aware of the modules/peripherals being used and...
Hi,
I noticed there is no SWO support mentioned in Product Specification 1.1 for nRF9160. But since the architecture seems similar to the nRF52/nRF53 that have SWO under...
I have been interfacing with the Macronix external flash via the nfrx_qspi library for logging. While I am able to use nrfx_qspi_read() to obtain my log data, I am also able...
PM_MCUBOOT_STORAGE_ADDRESS and PM_MCUBOOT_STORAGE_ID seem to be no longer defined as of SDK1.2. As per the discussion here , I tried using DT_FLASH_AREA_STORAGE_OFFSET which...
Using nRF52811, Segger SES, and SDK 16.0, I have some times that seem to be off by ~2X.
I'm timing by setting a gpio before and after the event and capturing with a scope...
Hi
Referring to
https://devzone.nordicsemi.com/f/nordic-q-a/58652/additional-questions-to-nrf52832-errata-220-clearification/238659#238659
From the above post, the...
I am new to the nRF9160dk board. I have been able to compile and run some of the sample programs. I am now looking to have a simple program to talk to external uarts 0 and...
I need my sara sara-r410m-02b ublox module to connect to the cellular network using at commands. For this reason I require to send the commands by means of programming lines...
Hi
I have a custom who is using 52832 to develop a Bluetooth door lock, including a NB-iot module, The door lock is unlocked via app Bluetooth.
the question is : There...
Hey all,
Have just been messing around with the board, everything was working fine until I tried to follow this guide to install CircuitPython onto the nRF. I got it into...
Hi there!
I am currently trying to follow the SDK instructions to get everything up and running. I followed all steps closely and didn't run into any errors apart from the...
Hi there,
Because of the current corona virus I could order a debug in/out cable for the Segger's build-in debugger (P18 & P19). But I have the cable it self and slot compatible...
We'd like to be able to store a few items including mutable keys, and unique identifier in each device that is generated on initial boot of the product. I'm just starting...
Is it possible to pair the nrf52 DK and nrf52 dongle through bluetooth? My project requires that the nrf DK sends data (sensor values) to the nrf dongle, and from the dongle...
