I have been testing the thingy91x and measuring power consumption trying to reduce it to the absolute minimum.
Using a test program that moslty sleeps ( using k_sleep()...
Hello,
I'm working on a project using the nRF52840 and Zephyr, and I'm experiencing an issue when trying to use device power management (PM) with a custom sensor driver...
Hello,
I am new to nRF development. I am going through the nRF Connect SDK Fundamentals course.
I wanted to configure a GPIO on the nRF52833 DK board as an output and...
It seems that I'm getting different results reading QSPI flash from the APP vs MCUBOOT, with the exact same configuration. Writes appear to work fine from either, but MCUBOOT...
I am trying to get the wifi stack to connect to a wifi AP using WAP2 Enterprise (initially just with identity and eap_password, later with full ca_certificate check and client...
I've got some timing-issues with the nPM2100. As I could not locate the relevant information in the datasheet, I'm requesting this here.
My PCB has an nPM2100 with a mechanical...
Hi,
i acheived writting code that reconnects sequentially with multiple reflectors for my 1 initiator. When i am indoor i had good results, but yesterday i tried it with...
Hello,
When using the nRF Master Control Panel I see other Beacons with "Complete Local Name"... I am building an iBeacon but have not found a way to set the name and have...
The following thread talks about CPU unblocking during connection intervals.
devzone.nordicsemi.com/.../
How does this feature affect BLE Radio Notification? Do...
Hello,
I would like to develop a custom key sharing algorithm for nRF8001 chips. As far as I have understood the only way to use full 128-bit temporary key (TK) is OOB...
Good Moring engineers.
I just got nRF24LE . I am wondering the timer2 only provide 2 seconds long period ?
I want my project nRF24LE sleep as long as possible , at less...
I am using an RTC for other purposes that exposes a buffered 32kHz clock. I am considering using the buffered (rail-to-rail) for also the LF timebase of the nRF51. The drive...
I've just discovered that the Jlink LITE programmer can not program my custom PCB because it runs at 2.7V.
Does the nRF51-DK board support programming an external target...
Hi....
We are working on PCA10028 DK with S130 softdevice version 0.9.0 alpha. Could you tell me about the release of stable SD S130. Hope it will be soon.
Hey,
Is it possible to use the NRF51822 for connectivity together with Arduino, and if so are there any easy instructions as to how to do so? I am looking something on...
Hello I was wondering if I can use both the proprietary protocol 2.4 Ghz ( I understood the one to use for the new projects is Gazell ) and the Blueotooth smart on the nRF51422...
Recently,I met a problem when I used Gazell mode. Before, i used the GPIOTE to collection PPM receiver 's length of time, when I also use the gpiote and wireless data transmitting...
Hello , i have been following the ANCS tutorial and have managed to pair it with my iOS device. I am using the Nrf8001 with an arduino. I have read up many articles about...
I have seen several good questions and answers on this forum regarding the use of a PA for extending range of the nRF51422/nRF51822 devices. I have a battery-powered application...
Hello everybody,
We are using a nRF51288 with an external DCDC converter. VDD and AVDD is bridged, DCC is not connected.
The software is working in Peripheral mode, S110...
hello,
I recently purchased a NRF51 dongle and NRF51 DK. I was working with older version of NRF51 development kit. I did n't get any information in the user guide provided...
Hello,
when using the S130 with multiple connections and sporadic advertisement and scan procedures, I get a connection timeout after a few minutes, now I must know, how...
