I am trying to get a WiFi project working using the nRF52840DK and nRF7002EK . I use a 3.3V power source that is supplying power to both nRF's in parallel. For the nRF7002EK...
Hi,
I'm developing firmware for the nRF52840 DK using nRF Connect SDK v2.9.2 , and I’m running into a problem that didn’t occur in v2.8.0 .
My project uses Zephyr and...
I am receiving an error when connecting to a custom board by running nrfjprog --reset, any similarly with any other commands that require connection.
I am connecting through...
We have previously used nRF52840 and for the latest iteration of our board design we are updating to use nRF54L15.
We are aware that for nRF52840 we could map any pin to...
Hi,
I faced with an initialization issue of combination two features: MCUMGR and UART_ASYNC_API. I get a crash right after the FW starts. It looks like the SW configuration...
I checked the nrf52832 manual and found that both XC1 and CX2 are analog input pins for the 32Mhz clock pin configuration. The reference design for both uses 32Mhz crystals...
Hello, I need to configure and compile a sample to send an audio stream (mp3) to the I2S interface.
I tried to put together some configuration from other samples but no...
Hi, I have two different types of nRF24L01+ modules, both behave differently.
The "troublesome" module always has TX_DS asserted after a transmit, which is the same behavior...
Hi,
I am using the SPI Master 1 to control an EEPROM. I used the spi_example project to help get the code working. It all works fine if the code that initiates the SPI...
We have designed a differential antenna for the nRF51822 CEAA chip.
Each of the RF output connects through a matching circuit to each one of the two 50-ohm to ground end...
How to setup MQTT for CloudMQTT? I have working raspberry PI I can ping and connect to device when follow the user guide. Now I like to try MQTT example but don´t know how...
Is there a list of every interrupt these functions effect. Specifically I am worried about
static void ble_evt_dispatch(ble_evt_t * p_ble_evt)
My assumption is that...
Is there any S110 demo with good communication between periphera and APP in phone side in SDK 6.0? It means that data channle works well from 51822 to APP and APP to 51822...
Is there any S110 demo with good communication between periphera and APP in phone side in SDK 6.0? It means that data channle works well from 51822 to APP and APP to 51822...
The nRF51 series reference manual v3.0 documents 3 Real Time Counters: RTC0, RTC1 and RTC2 (pp 17 and 109). However, RTC2 does not appear in the SDK documentation (e.g. no...
when I download program(pin_change_int_example) in nrf51822, Immediate Interrupt is occured
And when I push the button, Interrupt is stop...
What is problem?
I want...
Hello,
I am designing a board based on the SoC nRF51822. Since this is a homemade project I do not have lab equipment so I can not measure antenna impedance and therefore...
I'm trying to pull my project out of the examples directory, but there seems to be many dependencies on files far outside my project, and files not shown in my project file...
We use Laird BL600 module in our design. Laird engineers has informed us, that to update softdevice firmware of Nordic nRF51822 chip inside module they use Jlink adapter over...
Hello,
i've already read a lot about this topic in this forum, but now I'm unable to continue on my own. I wan't to migrate the DFU SDK emaple from Keil to GCC. I already...
Hello,
I am trying to use the nrf24l01+. But I don´t get any signal in the MISO pin. I have the same behavior in all my nrf24l01+ devices.
The MISO pin as always HIGH...
