Hi Team,
We are implementing an UART communication between a M4 processor (UART master) and a nRF51 (UART slave) and we want to use the UART in Low Power mode with flow...
Hello everybody,
for my project, i will bond the peripherial with the central.
I test my device with the MCP and can connect without problems. When i press the Bond Button...
Hi all,
I am trying to count the positive edges of a 3.5MHz signal with GPIOTE, PPI and the TIMER1. Unfortunately i can only measure to frequencies up to a little more...
Loaded Softdevice S140, ( Using NRF52840 DK board ) using NRFgo Studio.
App flash base is set to 0x00021000 and app RAM base is set to 0x20003000
Looking at the CPU...
In our earlier projects with nRF51 and SDK 8 we used to have bluetooth device names of length 13 or 14 characters. However, when using nRF52 and SDK 12 I noticed that the...
Does the Antenna in this Beacon relates with this "BAL-NRF02D3 '50 ohm balun transformer for 2.45GHz ISM"? Any idea what's this "BAL-NRF02D3" for? many thanks!
I am using a eeprep tool which can only be used with command prompt. I am struggling with it.
Here is the format to use eeprep tool :-
usage: eeprep [options] <infile...
Hi,
I'm trying to get the SPI Slave example working on my nRF51822 PCA100001 development kit.
SPI1_TWI1_IRQHandler never gets called even though the ACQUIRED and...
Looking into the schematics, I could not find any uart or spi signals on the connectors. I am good in soldering, but I would not dare connecting wires to the nrf51422... ...
Hallo everyone!
I need very low consumption when BLE working. according to S110 SDS, BLE power profile section, when BLE in idle-connect, there is Ion+Irtc+Ix32k, same...
Use the spi_master_example_with_spi_slave in SDK6 to evaluate the SPI master module but fail.
No matter use the default pin assignment or re-assign, it does not give out...
I can't find in the documentation for the IoT the usual section about requirements for the start of user code, the start of user RAM, the max stack used and whether any heap...
I would like to be able to generate DTMF tones using PWM. I am very familiar with the process, having written code to do this several times on other devices. The DTMF will...
Is it possible to use the nrf51 dongle with raspberry pi b+ ? I'm prototyping a 6LoWPAN solution where the peripheral nodes are nrf51 devices. I'd prefer the central device...
Hi, I'm not used to the bsp.c so my question could be silly. I hope you could understand.
When I used SDK 6.1, the example about button_event_handler function had a parameter...
What is the best way to transfer an array of individual values using the BLE stack?
Is it by appending all the values into one blob and sticking it into a characteristic...
I'm using
HID keyboard example (SDK 7.2), Softdevice S110 7.1 , IAR for ARM 7.1, J-Link,
on my custom board (with NordicSemi nRF51822-QFAA MCU).
/***************...
I am designing a product with the nrf8002 chip and have a question on Power consumption. Lets say I leave all the default ratio's alone and use a CR1620 battery which has...
How can I read the Bluetooth clock (piconet) which is synchronized between the master/slaves in the piconet ? I need a constant (micro second accuracy) time from when I do...
Hello,
Is it possible to know the preamble , data format and the CRC calculation to interface a radio system ( GFSK Manchester) with NRF905 ?
Thank you
I'm wondering if the port and pin function can be used together to configure a set of pins.
For _port_dir_set, I assume it sets the whole port to the designated direction...
