Hello!
I am working with the example mpu interface projects located at the following repo:
github.com/.../nrf5-mpu-examples
After converting the Keil projects to...
I'm using S332 0.9.1 with freertos. nRF52.
BLE and ANT are both active. I would like to run the ANT continuos wave (CW) test after a specific trigger (a command over a console...
I want to encrypt advertisements using aes-ccm peripheral present on the nrf51 board. I am not using softdevice, instead I am generating my own packets and transmitting them...
Currently, it using the I2S at nRF52832.
I want to play the wave file,But can not play well.
So, I ask you for a check because there is the following question.
[Question...
We love the radio range of the Nordic bluetooth chips. I am looking to see if anyone is developing a long-range bluetooth pendant or wearable? if so, I interested in perhaps...
I'm trying to read 8 adc channels using SPI, but then if I dont put some nrf_delay_ms the MISO return nothing and the CS is being driven low by default, high or a period of...
Does rbc_mesh_value_enable() API is designed for ? and how should I use it? and what does its parameter handle mean? Is it has the same meanning as the parameter handle of...
I am working with the nRF52 DK, using SDK v14.2.0 and SoftDevice S132.
After removing all BSP functions from the BLE UART example, I am setting up LED1 and LED2 of the...
Hello,
I'm trying to get the FDS to work, but it's giving me a headache. I'm using SDK 13.1 and S132 4.0.2 on a NRF52832.
In the beginning I thought I had that issue...
Hello,
I am trying to figure out my problem related to this question .
I am writing just a couple of words to flash with FDS. The problem is that after writing, the...
I am trying to use nfc_t4t_lib in NFC_T4T_EMUMODE_PICC mode. After receiving an APDU I am doing some calculations and sending reply with nfc_t4t_response_pdu_send. If calculations...
What is the best way to store the values of my attribute data?
With my current code, from the tutorials, the read, write and notify works fine.
But I need to store the data...
Hello
I noticed that since S132 v3.x.x we can configure the MTU. Does all the posts referring to long writes in this forum apply to the situation before this feature ?...
Hi
on nrf52832 ble_app_uart how can change MTU size and LL payload size?
have any source ? or example ?
or any change MTU and payload example ?
( for BT4.2 ~ BT4...
Hi,
I'm using SDKv14.1 on nRF52810. I doing the DFU according to the ble_app_buttonless_dfu example. When I use sd_ble_gatts_service_add to add service UUID in the ble_dfu_buttonless_init...
By testing the source example of throughput example of S132, it is known that throughput is mainly affected by four factors.
1, ATT_MTU
2, DLE
3, Connection event...
Hi Nordic team,
Currently our company under developing the product using NRF52840 + S140 Softdevice.
Now we prepare to list our product with Bluetooth SIG but after...
Hi,i have some problems at fds in sdk14.1 ble_app_buttonless project.
1,fds_register() & fds_init();
2,fds_record_write();
3,fds_record_find();
4,printf the record...
Hi guys,
Right now, I'm trying to do some throughput measurements via the experimental ble_app_att_mtu_throughput example. This using the SDK 14.2 and S132 on two nRF52832...
Hi,
I have seen some curious behavior with the FDS module. I'm using nRF5SDK 14.2.0 with s140_nrf52840_5.0.0-2.alpha, with FreeRTOS. In short: In some cases it seems that...
Hi!
I want to get infinite advertising.
My advertising gets timed out in 180 sec.
I have set to Fast Advertising Mode.
Below is my code
static void ble_evt_dispatch...
