I've a PCA10036 V1, I change the IC to nRF52822 QFAA-B016. With nRF5_SDK_11.0.0-2.alpha_bc3f6a0 and SD: s132_nrf52_2.0.0-7.alpha_softdevice, the programme started but if I...
Hi
We are developing software for the nRF51 with Keil under VirtualBox. Previously we used the PCA10000 dongle with the Master Emulator and MCP without issue. Now, with...
We are using nRF51822 for our products.
We want to know the min value of "Receiver sensitivity" when we use this chip for BLE.
The Datasheet says "Receiver sensitivity...
Dear
The BLE Multi-link example (ble_app_multilink_central and ble_app_multilink_peripheral)
shows how one central device can connect to multiple peripheral devices. ...
In the MCP app, if I have the following service data for an Eddystone beacon:
0x10, // Eddystone-URL type
0x00, // TX power in dBm. This is a signed integer so 0xEE ...
I have the nRF Control Panel Android application. It works fine with several BLE devices, but specifically for the Fitbit Flex, it fails to connect.
I know Fitbit wristbandes...
Hi,
The situation:
I was able to successfully receive known packets from a device running gzp_device_dynamic_pairing, from, the host running the gzp_host_dynamic_pairing...
Hi,
I am working on another project.
I want to make BLE and USB BULK communication operate at the same time.
My development environment is Keil,
It uses nRF52840 and...
According to the point above
link text
i bought the thingy but i did'nt think about the jlink ..
you can add me to the advent calendar ;-> for a nRF52 DK because...
I understand that the connection parameters viz. connection interval, connection supervision timeout and slave latency are negotiated between the BLE Central and BLE Peripheral...
We currently have a SPI interface between MSP and the Nordic nRF52840. In the DTM documentation it indicates UART is used to command the tests. Is it possible to do this using...
Hi,
I have 5 nrf52832 and nrf52851 beacon boards. All nRFs working in the beacon mode. They all in the same room. I tring to get a list of the active beacons the module...
Started out with the ble_nus-exmple. Added logging of a sensor to flash, and got it to work in SDK11, even without using the sd_flash*-routines, but writing/erasing directly...
I would like to perform an OTA on the DWM1001 board which has a nrf52832.Where can i get the details an the range that can be achieved with employing ANT.Are there any test...
I am following Tutorial 7 on "Development with GCC and Eclipse" and I am working in the Windows 8.1. I have followed instructions from the tutorial for installing the arm...
hi,
i am using a nRF5240 DK for receiving multiple services and characteristics data from Nordic_thingy_52,to receive and print this data on UART i used sdk 14.2.0's "ble_app_blinkey_c...
Hi there~. I was working on a BLE RC car (BLE peripheral) using Nordic's nRF52832-QFAA MCU , Nordic's UART Service for motor control, and Battery Service (BAS) for battery...
Hello.
The development environment is as follows :
OS : Windows 7 Pro 64bit
IDE : Keil uVision V5.24.1
Python : 2.7
SDK Version : nRF5_SDK_14.0.0
DK : PCA10040...
I want nrf51822 to switch between 2 different advertising timeout. One will set advertising timeout with 20s, another will keep advertising.
Currently, I use following...
I have a server running on my Android phone. I looked at the service UUID encoded in the advert packet using and Wire-shark and confirmed my app is broadcasting packets. ...
I am trying to execute code that broadcasts (uses the Soft Device Ble stack) on target nrf52832 boards connected to the PCA10040.
I am successful uploading a program (that...
