Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Hi
I have done several projects with the nRF905. I know the device quite well. Normally I use the CD, AM and DR interrupt pins to determine the status of the device, my current...
i made this project to try to create RSC service on arduino
developer.bluetooth.org/.../runningspeedandcadence.zip
unfortunately the server starts but i'm not able to...
Hi,
I want to use hardware ECB encryption and decryption in 52840.I had tested the demo from nRF5_SDK_13.1.0\examples\crypto\nrf_cc310\aes\pca10056 . However,i can't find...
When using the APP_TIMER in SDK14 I am having a problem with the application stopping.
I was using the APP_TIMER to flash LEDs and watch for timeouts in SDK13. when porting...
in the sdk_config.h there are plenty of definitions, where "31" is used as a non-valid PIN value
This is destructive if you want to use p0.31
For example:
If one uses...
Hello. I want to use the same pin on nrf52832 for wake up and system off, however I have some issues, like sometimes it doesn't wake up or it is needed to press button few...
When I use sdk14.2 nRF52810 ble_nus_string_send to send data to a mobile phone android, the first connection is no problem, but disconnected again after connecting problems...
Edit: I'm using the softdevice S110, 8.0.0, Nrf51822 chip, Keil uv5.12
Edit #2: Added more detail and revised certain description.
What's the problem?
My program...
Dear partner,
1) Our custmer want the spec of S140, I cann't find that on the inforcenter. can you give me one?
2) By the way i want to know where is my mypage case...
I want to have every node carry a copy of the sensor data in every other node and pass these around on update.
Should I use ANT FIT or FS? What makes mores sense?
As the...
Hello,
How can I detect how much RAM is still free on the heap during runtime, without a debugger attached, just from within the application?
Cheers
Trax
Hi
Can nRF52840 PDK support UART buad rate 921600/1000000 correctly?
I am testing UART with below example for our product development:
nRF5_SDK_14.2.0_17b948a\examples...
Hello, I have problem during dfu otau over ble connection. I use linux version of the nrfutil - my OS version is Linux-4.9.0-3-amd64-x86_64-with-debian-9.1 In some cases i...
I am trying to enable SPI in spi_config.h but SPI3 is missing for the nRF52840.
I need DCX functionality, and from the OPS for nRF52840 it looks like it is only SPI3 that...
I'd like to use DFU to update the SoftDevice of an nRF52810. Based on the documentation it looks like the new soft device needs to be copied into flash while the active SoftDevice...
