Hi,
I'm using redbearlab's nrf51822 board. It is a arduino compatible board and hence it is using 0,1 (mapped to 9 and 11 for nrf51822). How do I make printf print to this...
An external PA/LNA is used to extend range of nRF51822, and S110 is used for BLE, How to switch between PA and LNA? and how to disable PA/LNA when there isn't transceiving...
Hi...
Can anybody help me to run ble_peripheral example (ble_app_hrs for S130). I have build and load the code successfully but cant see the advertisement. But while debugging...
I am working with the nRF8001, and I'd like to create a services.h file that will let me broadcast battery level and as well as allow temperature to be read by a peer.
...
Hi We have an application where we what to read i2c sensor data over the air to an iPhone. We've taken ble_app_uart_S130 project and grafted in some twi_hardware code. There...
I am interested in the S130 ability to hold 3 central -> peripheral links over BLE, and am looking for some evidence that this has been accomplished with extremely low-power...
I'm trying to implement channel scanning in our nrf24lu1p based USB dongle.
I'm following the specs and basically loop though each channel ;
loop
stop listening
set...
What is the best way to store the values of my attribute data?
With my current code, from the tutorials, the read, write and notify works fine.
But I need to store the data...
Hello
I noticed that since S132 v3.x.x we can configure the MTU. Does all the posts referring to long writes in this forum apply to the situation before this feature ?...
Hi
on nrf52832 ble_app_uart how can change MTU size and LL payload size?
have any source ? or example ?
or any change MTU and payload example ?
( for BT4.2 ~ BT4...
Hi,
I'm using SDKv14.1 on nRF52810. I doing the DFU according to the ble_app_buttonless_dfu example. When I use sd_ble_gatts_service_add to add service UUID in the ble_dfu_buttonless_init...
By testing the source example of throughput example of S132, it is known that throughput is mainly affected by four factors.
1, ATT_MTU
2, DLE
3, Connection event...
Hi Nordic team,
Currently our company under developing the product using NRF52840 + S140 Softdevice.
Now we prepare to list our product with Bluetooth SIG but after...
Hi,i have some problems at fds in sdk14.1 ble_app_buttonless project.
1,fds_register() & fds_init();
2,fds_record_write();
3,fds_record_find();
4,printf the record...
Hi guys,
Right now, I'm trying to do some throughput measurements via the experimental ble_app_att_mtu_throughput example. This using the SDK 14.2 and S132 on two nRF52832...
Hi,
I have seen some curious behavior with the FDS module. I'm using nRF5SDK 14.2.0 with s140_nrf52840_5.0.0-2.alpha, with FreeRTOS. In short: In some cases it seems that...
Hi!
I want to get infinite advertising.
My advertising gets timed out in 180 sec.
I have set to Fast Advertising Mode.
Below is my code
static void ble_evt_dispatch...
Hello,
I'm following this BLE services tutorial . I have added the functions required to create a service.
In the our_service_init
void our_service_init(ble_os_t...
Hi guys,
Currently, I am developing a application on nrf51822 which requires writing values on flash to store in case of power down. However this values need to be updated...
I have a nRF51822 smart beacon kit and a ST-LINK V2. I read the documentation found on nordic's website, downloaded all the programs that the documentation requested etc....
Looking through the ESB implementation in SDK 14.2, nrf_esb.c I notice it uses
#ifdef NRF52
on several places. In nrf.h, the "old" NRF52 gets re-defined as NRF52832_XXAA...
I tried every configuration I can think of to reload firmware on the DK with JLINK drive when PPK is piggybacked. The only way I can get the firmware to load on the DK is...
