Hello,
I would like to do an communication between Arduino and Android platform.
In my case, Android will be master.
But I want also test between 2 Arduino with an Bluetooth...
Hello,
I would like to develop a custom key sharing algorithm for nRF8001 chips. As far as I have understood the only way to use full 128-bit temporary key (TK) is OOB...
i am useing nRF51822 pairing with nRF24lu1 over GZLL protocol now,
is there someone have the experience on how to config the parameter of GZP_TX_RX_TRANS_DELAY in function...
I have a peripheral running the S110 stack, which presents a characteristic to which I want the central (running S120) to be able to do a long write. What I've been trying...
Hi all,
I have been trying to combine the UART and hID Keyboard examples into a single application.
I want to use the HID part to send specific keystrokes using buttons...
Hi, I'm new to BLE and just started feasibility testing, using RF8001, on a small device with no IO. The device will have a unique code set at factory, and printed on label...
I'd like to be able to enable/disable the S140 SoftDevice multiple times during operation (SDK 14.2.0). To achieve this I'm using `nrf_sdh_ble_enable` and `nrf_sdh_ble_disable...
Hi,
Im trying to modify secure_bootloader demo in SDK_12.3, to use timers. I modify nerf_dfu.c file in libraries/bootloaders catalog. I want to achieve bootloader wait...
I am using MasterEmulator.dll for connecting to pear device.
I am using nRF51 Dongle and pear device is nRF52 custom board.
The pear device is advertising at very low...
Hello,
we have custom boards with nRF52832 chips, which show different behaviors in low power system ON mode. The current consumption is pulsing at around 22Hz to ~34Hz...
HI.
I purchased the nRF24LU1 + chip and created a USB Dongle module.
I have come to know about PID and VID.
Can I use nordic's VID (0x1915) as it is?
Is USB Dongle...
Hi ,Nordics
when I use my host device (reffered to the example of ble_app_hrs_c)to pair and bond with a peripheral device(a gamepad) ,the pairing failed .I don't kown...
Hello....
Is there a way to configure the SPI peripheral(s) to run at a custom bit rate (frequency)?... For example: Run SPI at 3.4MHz.. or any other custom frequency that...
Hello all,
Do you advise to have 2 SPI interfaces - one for the sensors we're using (accelero/ gyro) and another one for the SD card? if so, when adding an SD card to our...
Hi team,
i am having a custom board i want to program soft device and application using external j link. i came across nordic website in this page http://infocenter.nordicsemi...
Hello All,
I am a beginner to NFC OOB, so can you suggest me some good learning materials regarding NFC OOB pairing as I wish to do so between my mobile phone and the...
Good Morning Team,
Hope your day is going well!
Could you please provide the IPC 1752 document and RoHS CoC (2015/863/EU) directive document for below part since it is...
hi hi ;
i'm trying to control gpio pin 20 with my smart phone and with event at gpio pin 5 (when the state of the pin 5 changes the gpio pin 20 toggeles ) but my problem...
Hi, can someone explain in simple terms how it works?
I don't really have a clear concept of what a replay attack is, but I suppose it has something to do with recording...
Hi,
I am facing the same issue for all of the node.js examples.
It says: Connected! Error: command disallowed (oxc)
Also is says: Service uuid XXXXXXX not found!
...
The nRF52 SDK ANT example "ant_scan_and_forward/" configures a device linit of (16-1)=15 in this line:
// Public Definitions #define MAX_DEVICES ((uint8_t) 16) /**< Maximum...
