Hello,
I would like to develop a custom key sharing algorithm for nRF8001 chips. As far as I have understood the only way to use full 128-bit temporary key (TK) is OOB...
i am useing nRF51822 pairing with nRF24lu1 over GZLL protocol now,
is there someone have the experience on how to config the parameter of GZP_TX_RX_TRANS_DELAY in function...
I have a peripheral running the S110 stack, which presents a characteristic to which I want the central (running S120) to be able to do a long write. What I've been trying...
Hi all,
I have been trying to combine the UART and hID Keyboard examples into a single application.
I want to use the HID part to send specific keystrokes using buttons...
Hi, I'm new to BLE and just started feasibility testing, using RF8001, on a small device with no IO. The device will have a unique code set at factory, and printed on label...
I had the same experience as fishman and I went back to give Eclipse a try. (Post: nRF Beacon does not build on Android studio) I tried to build it in Eclipse Luna with the...
When using the BLE device, BLE_GAP_EVT_DISCONNECTED event informs us that connection between dongle and BLE device was closed/lost.
Is there a way to know when dongle connection...
Every time I change a common source file within Kiel, the source file is changed for every project because (obviously) is a file common to all example projects.
Is there...
Is there a nordic guide which lists out the steps taken by the chip when going though a bonding process? I am trying to add as many RTT printouts as possible to know where...
finally I have done to implement that ADXL345 can throw data over BLE using nRF UART app service with this code . now my problem is how to change 2's complement ADXL345 data...
Hi,
We are using a nrf52832 in a serialized application with a STM32F4 and standard SPI as the transport layer. We are using the SDK V12 on the STM32 and softdevice S132...
Hello,
I want to add DFU fonction on my custom application. The final goal is to update my firmware from my custom app (not just once).
My setup is : SDK11 - nRF52832...
Hello All,
I am using the HRS example as reference from Nordic SDK14.1.
I have one central and 4 peripheral devices.
I have the MAC ID's for all the four peripherals...
Hello Nordic Experts,
I have One central device and and 4 peripheral devices.
At this point of time I am trying HRS example on it, the example is running fine with single...
Hi everyone,
We are trying to choose which protocol use for connecting devices based on Nordic SoCs.
We use devices in following way:
about 300 - 500 devices (wearable...
Hi there,
The dfu secure bootloader example is working fine with my nrf52832 sdk14.2 s132. but the experimental buttonless dfu in the example is not working for me. I was...
Hello,
I have nrf51 beacon that is protected from read. I want to recover it (erase and disable protection) but I only have st-link programmer. How can I do that? Maybe...
Hi,
I have been developing with nRF51 for some time and already implemented a nice 13.56MHz wireless charging circuit. Now that I'm moving to nRF52 I would like to keep...
Hello,
I have bought a bunch of nRF24L01+ chips online and just received them. How can I tell if they're genuine or fake? The markings are 24L01+ and 1712AB.
The boards...
Without making use of white list approach, can a BLE peripheral reject connection request sent by a BLE central?
I want my application layer to be notified when the BLE peripheral...
Hi,
DevZone displays incorrectly when single word length exceeds the width of the #ContentLeft
div. Instead of wrapping, it expands the div to accommodate, clobbering...
Hi all,
I'm using the nRF iOS Toolbox as a reference to design an app.
Can someone please help me in terms of which swift code file I need to use to read and write data...
