I'm looking at interfacing a typical Wheatstone bridge sensor to the nRF51822 ADC. This particular sensor only requires a mA or two for excitation and the output fits within...
When use the "nRFBeacons" app to update the info on my beacon the following happens:
Go to update tab.
Select "Connect"
Press "SW2" on beacon and see the LED begin flashing...
I am using s110 and nrf51822. I've set up up a long characteristic of 154 bytes.
Sending between 1 and 154 bytes works as expected.
Sending 155 - 160 bytes gets rejected...
Hi,
I tested the nrf beacon application, it allows only the beacons with company identifier 0x0059 (nordic's id). But i need to modify it to support all the device, how...
I use a app_timer_create() function to create a task(200ms once)
when in the task_timeout_handle() ,
I do something more than 200ms,
what will this timer going ?
Hi!
I use nrf51-pwm-library ( github.com/.../) to control brightness of LED RGB light source and it works ok till I don't want to adjust brightness slowly (dimming function...
hello,
are there any completed sample code of using pwm0, 1?
just 2 or 3 word can working like following? or need other config?
pwmcon=xx;
pwmdc0=xx;
pwmdc1=xx;
also...
Hi,
I am designing a custom PCB with the nRF52832, I am going to use wire bent antenna over it. Can I bend feed wire by 45 degree. I have attached image for the part I am...
Hi All
I am using the example of uart in SDK10 wit nordic 51822
First of all ,I add a PA with 51822 to increase the signal of BLE, but I notice that the speed of PA is...
I can read peer address and rssi field in the scan request report. But how can I read the AdvA address field in the scan request to make sure that the scan request packet...
Is there a method to remove a node from the network using the current bt mesh stack? I've looked through device_state_manager.c but it appears to me that there are only functions...
Hi,
I am using 2 nRF52840 DK to build a network, One is the client and the other one is the server. Both of them are connected to computer with USB cable.
I would like...
hi,
i test my project for i2c sensor module, the debug found have error what there are the following error tips.
..\..\..\swct_application\i2c_sensor_driver.c(14): error...
Hi,
I'm trying to write custom boot loader, that receiving hex file via uart and write it to location 0x40000 and then jumps to the location. I changed FLASH_ADDRESS and...
Dear experts,
We are evaluating to perform Round Trip Time (RTT) measurement for ranging application. The accuracy requirement is 1m to 2m. Are there any sample applications...
Hi,
I am using a custom board which I designed based on the Puck-js board, except that I am only using an I2C based distance sensor instead of the other devices onboard...
After experiencing UART problems without handshaking I opted to enable hardware handshaking.
Where RTS & CTS are pins 5 & 7 respectively.
I was experiencing overrun (insufficient...
The nRF6905 nRFready Basic Remote is a complete hardware and software reference design for basic 2.4GHz RF remote controls.
What nRF24LE1 devices are included in the hardware...
hi sit and test bluetooth mesh and i do not quite understand how the client knows that the server is off or on and there is a way to find out if a server is on or off
Hello,
I would like to use nRF52840 in order to make some BLE5.0 mesh products. When I open the nrF5 for mesh, I can see only examples for nRF52832.
Do you know if these...
hello, i am trying to implement external RTC in my application. i am using the SDK 14.2.0 and softdevice s132 .n also for external RTC using the M41T62 with nrf52832DK. so...
Maybe there's a secret I'm missing but this looks like a development / debug flag that got left in.
I'm porting an app from SDK11 to SDK15, when I call app_button_init(...
