Hi all,
I am new to Nordic semiconductor but I could be interessed by nRF9E5. To check if it could fit my requierement, I would like to know if it possible to configure...
Hi,
I am using ADC without external reference and no analog input in order to measure the battery level with a timer (code at the end).
I am also reading several ports...
Hi,
I'm programming the nRF51822 and save some user data into the FLASH by using pstorage_update . It works fine if I set system off mode, and wake it up. I can read back...
Hi,
I have been using nRF51822 with my Android app using Android's Bluetooth Low-Energy APIs.
In order to get more details, I am currently working on integrating the Android...
I'm looking at interfacing a typical Wheatstone bridge sensor to the nRF51822 ADC. This particular sensor only requires a mA or two for excitation and the output fits within...
When use the "nRFBeacons" app to update the info on my beacon the following happens:
Go to update tab.
Select "Connect"
Press "SW2" on beacon and see the LED begin flashing...
I am using s110 and nrf51822. I've set up up a long characteristic of 154 bytes.
Sending between 1 and 154 bytes works as expected.
Sending 155 - 160 bytes gets rejected...
Hello,
I am working with the BL652 EVK from LAIRD. The EVK has nRF52832 IC inside of the module. I downloaded the " nRF5_SDK_15.0.0_a53641a" and trying to use "ble_app_uart_pca10040_s132...
Hi. I am trying to develop an multiprotocol test example using SDK 15 and nRF-IEEE-802.15.4-radio-driver on NRF52840 dk board. I need that BLE and 802.15.4 stuff can work...
I have a confusion about mac address of nrf51822, I run example ble_app_uart .
When I use nRF Connect on Android, I can see the mac address of nRF51822 is CB:16:04:4A:10...
Hi,
I use nrf52832QFAA, SDK 11.0.0, Softdevice 132 v2.0.0. I need to add a device_manager_central to my project (in my project it's easier and faster than adding a peer_manager...
Hello,
In the documentation for nrf_serial_write function (SDK 14.0.0) it is written:
timeout_ms Operation timeout, in milliseconds. Pass 0 to operate in non blocking...
Hello friends,
I am trying to flash a nrf51 dk with keil5. When I try to flash it with a multilink universal I get this error:
My settings are the following:
...
Hello everybody !
My code is based on the code of the "ble_app_multilink_central" on which, I added some of the code "ble_app_uart_c" for the initialization and the event...
Hello friends,
I am trying to use the standard uart example of the SDK 11 with the nrf51 dk and trying to update the device's name via UART. I want to save somehow the new...
Greetings,
I can get the ble uart example to work on my PCA10056 using the example hex file, but when compiling the project on the SDK 15.0 S140 it doesn't work. Specifically...
Hi,
I can't found anything in the nrf52840 documentation about the ble antena directionality. I want to use it for indoor location, so i would like to know if it is omnidirectional...
I'm sending int16_t thanks to a custom BLE Service.
I receive well the data on the nRF Connect app (Android), but the data are displayed in hexa, for example for 256 I got...
Hello,
I'm developing an application that will run on a board without externel oscillator for RTC1 and it means no app timers support.
I started from ANCS example and...
Hi, I tested to run BLE Mesh(v1.0.1) light switch example using SEGGER embedded studio(SES) on Windows10 and three nRF52DK(ntf52832) boards .. one client, two servers. It...
Hi,
I encounter the problem when using the mcuboot with zephyr 1.11 is that the system keep rebooting.
mcuboot: https://github.com/runtimeco/mcuboot
mcuboot build...
