I'm looking at interfacing a typical Wheatstone bridge sensor to the nRF51822 ADC. This particular sensor only requires a mA or two for excitation and the output fits within...
When use the "nRFBeacons" app to update the info on my beacon the following happens:
Go to update tab.
Select "Connect"
Press "SW2" on beacon and see the LED begin flashing...
I am using s110 and nrf51822. I've set up up a long characteristic of 154 bytes.
Sending between 1 and 154 bytes works as expected.
Sending 155 - 160 bytes gets rejected...
Hi,
I tested the nrf beacon application, it allows only the beacons with company identifier 0x0059 (nordic's id). But i need to modify it to support all the device, how...
I use a app_timer_create() function to create a task(200ms once)
when in the task_timeout_handle() ,
I do something more than 200ms,
what will this timer going ?
Hi!
I use nrf51-pwm-library ( github.com/.../) to control brightness of LED RGB light source and it works ok till I don't want to adjust brightness slowly (dimming function...
hello,
are there any completed sample code of using pwm0, 1?
just 2 or 3 word can working like following? or need other config?
pwmcon=xx;
pwmdc0=xx;
pwmdc1=xx;
also...
I have been trying to integrate support for multiperipherals into my application, but am continuing to get errors when attempting to start advertising after the first connection...
As I don't know much about audio,I have trouble with the gain of the pdm module in nrf52832.Now
I have used MP45DT02 as the digital microphone,but I just can't understand...
Hi, I've searched and googled through this site and made sure no one asked this question before.
In core\Bearer_event.c, there is this function:
bearer_event_flag_t...
I'm trying to connect two nRF5 devices together, Central and Peripheral, and use a custom BLE service that I have written that has a custom 128 bit UUID.
I'm in the process...
Hi,
We are sending a data using Nordic UART Service (NUS), the data is transferred over BLE as a Indication.
From Message Sequence Chart in Nordic Infocenter
Here...
I am researching OTA procedures and I spent more than a few minutes wrestling with flashing soft devices and bootloader code to the nRF52_DK.
What I found is JLINK seems...
When adding extra buttons on breadboard for NRF52-DK do we need to use resistors OR i can directly connect one leg to GPIO pin i.e 30 and another to gnd.
I'm trying to use the nRF24LU1P as a standalone 8051 with the nRF24 radio inside. I provide 5v on the USB connection but no host connection. I am trying to operate in PRX...
Hello,
I'm using the nRF52840 development kit with the "« ble_app_att_mtu_throughput" example with version s140 6.0.0-6alpha.
What's the bitrate used in the long range...
I'm using nrf52832 in my peripheral device, I want to secure its connection via any authentication is there any method for that?, also I need to encrypt its data(characteristics...
Hello,
I'm working on a bootloader based on the examples in SDK 13.1. As we have expanded its functionality, I'm now wondering what happens when one of the steps in the...
Okay this got us going around in circles and it looks stupidly simple. It seems there is a knowledge gap since we saw many posts similar to ours but without clarity as of...
Hi,
I am getting data over thread and BLE network. I want to send the received data over uart.
Is it possible to use serial example to merge with thread server example?...
Hi,
We are having problems trying to integrate support for maintaining application context and bonding info across firmware OTA updates on our NRF52 (nRF52832) based board...
I just test nRF52840 DK with ble_app_att_mtu_throughput_pca10040_s132 example. I know BOARD_TESTER transmits 1024 dummy kbytes to BOARD_DUMMY. I want to replace dummy byte...
