Hi!
I use nrf51-pwm-library ( github.com/.../) to control brightness of LED RGB light source and it works ok till I don't want to adjust brightness slowly (dimming function...
hello,
are there any completed sample code of using pwm0, 1?
just 2 or 3 word can working like following? or need other config?
pwmcon=xx;
pwmdc0=xx;
pwmdc1=xx;
also...
I am planning to migrate to SD 7.0 and SDK 6.0 in order to use the static pass key capabilities. When using the static pass key how should security params be initialized ...
Hi Hakon.... when i compile my project i get some linker errors,
._build\gzll_host_ack_payload.axf: Error: L6218E: Undefined symbol __main (referred from arm_startup_nrf51...
I'm trying to perform communication between my device and iOS and I ran into some problems. For tests I'm using iPod touch 5 with nRF Toolbox and LightBlue apps and nRF51822...
I've been using Master Emulator API 2.1.3 in Visual Studio 2010 Express, and have spotted a fix I may need in 2.1.5 so I've switched to using the 2.1.7 API. However, I've...
Hello,In normal condition, I use UART,pwm,spi an so on.Now I want to clear the configuration, and enter System ON mode.But I don't want to system reset.
How should I do...
Hi,
I am developing a small development board of visiting card size, which is powered from a coin cell. I have two questions,
All i want know is there any polarity...
Hi,
do sd_flash_page_erase or sd_flash_write provide any guarantees that the command has executed successfully or should I do a manual check to verify if the page was really...
Hello all,
I am working on nrf52832 Board and i want to use it as translator to send and receive the data , please tel which pins i need to select as UART(rx,tx) pins ...
I am designing a custom board with nRF52840, powered by USB, no battery, using its internal LDOs to supply other peripherals with 3.3V
I have two questions about pins/outputs...
Hi
I generate a pwm signal via changing the state of one characteristic. In general, the pwm works fine. But the problem occurs when I add the timer which is responsible...
Hi guys，
I use the 51822's PWM recently, PWM is made by GPIOTE+PPI+TIMER, and the PWM source code as below(I use TIMER1, GPIOTE[0], PPI_CH[0], PPI_CH[1]， period and duty...
Hi all, I'm asking on both BLE specification version 4.0 (or more) and NRF51822 S130 about having support for multiple central connections at the same time while our NRF51822...
Hi,
I get RSSI values like -96 or -97 dBm before the coded PHY connection between two nRF52840 pdks drops. Are these values something expected? TI advertises sensitivity...
Hi, there~ Nordic's Mesh SDK is fascinating! I was thinking of a way how to connect the Internet with Nordic's Mesh devices.
From the web, you might have seen these...
Hello,
I'm working with the thread v0.10.0 sdk release and I would like to customize and add some new packages to the border router.
I see that there is a release tag...
On the BLE Secure DFU Bootloader page of the documentation, there is a typo. See ' Secude ' in the following text.
Configuration parameters
There are certain configuration...
We have certain boards having nRF51 onboard. We want to use them as sniffer. Unfortunately, pins that are used for UART on nrf51DK board are not accessible on our boards....
Dear Nordic Development community,
I have a very interesting project going on based on bluetooth speaker controls.
In short words, i'd like to control the sound level...
i am using uart communication between nordic and some device ,communication was fine upto some time but after some random amount of time i am getting uart_driver error...why...
