Iam trying to display the uart data as a scanned response.nRF51822 receives the data from PIC and it is displayed as scanned response during advertising.the problem is nrf51822...
Hi,
This is a bit more of a typo report.
In the Debug Logger doc page , app_trace_init() is supposed to return an int but in its function declaration it's said to return...
Hello All,
I'm trying to build a receiving unit using the nRF24L01+ and PIC16F628A. Im using an nRF24L01+ and RaspberryPi as my TX unit which i managed to get working ...
Hi,
We have a device using the S110 v6.0.0 softdevice and the SDK v5.2.0.
We started working from the Proximity application available in the sdk.
Is it possible to...
Hi,
I have a simple demo device that does play to be a mouse and a keyboard using HOGP profile. I can get it running with Linux pretty well and I can get it running with...
Hi,
I have a simple demo device that does play to be a mouse and a keyboard using HOGP profile. I can get it running with Linux pretty well and I can get it running with...
Hi,
I'm migrating from SoftDevice 6.0 to SoftDevice 7.0 and I'm trying to implement the DFU in SDK6.0. I am experiencing an issue where whenever the DFU begins(reaches 0...
This is a kind of continuation to: devzone.nordicsemi.com/.../
I'm modifying the bootloader_secure sample to implement encryption.
I'm now at the step where I need to...
Dears,
I am developing my application based on SDKv12.0.0. I would like to use "printf" & "app_uart_get"(interrupt routing) instead of "NRF_LOG". Is possible to switch it...
Hi,
I am asking questions through Google Translator.
The context may not be smooth.
I am planning one project.
Simply put, the usbd_hid_generic example uses bluetooth...
I use nRF51-Dongle as an ANT USB stick, to carry out this test, but the ANTware II can never display the informations of nRF51-Dongle. How can i do it ?
Hello,
there is an equation in the code where I see that variable: deviceid is: 229 and var_temp is also: 229.
But the debugging shows that the Mikrocontroller is going...
I'm seeing the same issue as this question , but I'm on SDK 13.1, which has a different peer_manager.c, so I can't directly use the fix for that question.
Like the other...
Hi,
Scenario:
Two nRF52832DK boards on a table, approx 20 cm from each other, +4dBm output power.
Payload length is ~60bytes.
Running at 1Mbps gives me less than...
Hi,
assuming I have an IMU sensor with 3 different interrupt lines. And I want to start a TWI DMA transfer for each interrupt line in parallel. Is this possible since there...
Hi all,
We are starting new project, the aim of the project is control street lights through web site by using gprs connetion.
The key requirements of the project is...
Hi
I finished preparing the nrf52832 board to use ppk and measured it with ppk.
I am trying to repair the nrf52832 board.
However, I do not understand the contents of...
Hello,
I'm porting the nRF8001 SDK to STM32 using HAL (CubeMX). Communication seems to run fine, however, the setup stops with CRC error. See abridged the logical output...
Hello everyone.
I am developing with nRF 52832.
However, when I call UART_init() function. my source code outputs an error message.
source code is under the line...
Hello, i'm using a nRF52840 on a PCA10056 and want to wake up from __WFE() with a minimum delay. When i'm using the debugger, i achieve a low latency but without the debugger...
Hello All,
We are working with one of the customer, where he is asking for range 200 meters between 2 nrf52Dk(nrf52832) and he want us to prove the same using two development...
