Hi,
We are running into a serious issue with OTA. Specifically, we have observed that nRF52832 will not be able to perform OTA to a newer firmware given that it is previously...
Hi all,
I'm trying to characterize the UDP throughput of a Thread network consisting of nRF5340 DK devices. I saw that Espressif made a test report and they seemed to use...
I’m using a custom PCB based on the Minew ME54BS01 module (nRF54L15 SoC) for both ends of our proof‑of‑concept: one node as a GATT‑based Channel‑Sounding reflector (leveraging...
Dear DevZone support,
I'm currently evaluating nPM1300 for Lithium Polymer battery management and charging and would like to ask a question.
I understand that I can...
Hi Nordic：
We are currently testing Zigbee on the nRF54L15 platform using the Zigbee R23-add-on-V1.0.0 SDK. It has been observed that when a low-power node disconnects from...
Hello, I am using ISP1907 which has NRF52833. I get the IQ data and configuration from serial as: DF_BEGIN ['IQ', 0, 0, 11, -9, -213] ['IQ', 1, 8, 11, -209, 23] ['IQ', 2,...
I have 2x Power Profiler Kit II up and running using the Power Profiler app - started twice and with separate PPK2 instances selected, as described in another support post...
I developed an android phone application base on the source code that was provided by nordic. Now I am trying to develop a PC version of what I made on the phone for lower...
Hi,
I am using NRF24L01+ as wireless communication medium. The NRF on PRX side interrupts MCU only once for recieved data. Although it sends ACK to NRF at PTX side. And I...
Hi,
I need to read data from MLX90615. It is a temperature sensor which follows I2C to read data. I got a sample code for this which is given below.
float receiveTemperature...
Hi all,
context: nrf52, iot sdk and ipv6; initially rpi as "border router"
question: What can be used as professional/industrial "border router" instead...
Hello,
Arduino start selling Arduino 101, powered by an Intel Curie processor.
As far as I have seen here , Intel Curie module integrates nRF51822.
I was wondering...
I'm in the process of trying to start my custom application based on the ble_app_multilink_central_s130_pca10028 example found in the SDK. When I run the app on the nRF51...
Hello everyone,
I am trying to use Segger Embedded Studio for a simple explerimental project.
I started from the sample FDS example from github and build something on...
Hello,
I have an application that uses the Soft-Device. That application want to start a SPI-Bootloader. That SPI-Bootloader isn't the only bootloader on the device, so...
Hi,
I have nrf52 setup as central and peripheral.
As central it connects to another peripheral and everything works just fine. After it did connect I turn of peripheral...
Hi,
I have the NRF52 dongle that is set up as the client and is searching using the ble_app_uart_c (Found in examples\ble_central) example and I am trying to connect a...
SDK11, nRF51422.
Is it safe to use pstorage and fstorage at the same time?
I want to use fds for data storage in my firmware, but device_manager_peripheral.c requires...
Hi, I am trying to read a 24-bit register (with 8-bit address) using the I2C (nrf52). And the timing diagram is given below.
Basically I created a 3-element array (24...
I am having trouble getting the experimental ble_app_multirole_lesc example working with Android and nRF Connect. It is working fine in iOS. I am using v12.1.0 of the SDK...
