Hi,
I’m working with an nRF52832 DK board that’s stuck in bootloader mode—LED 5 just keeps blinking. Here’s what we’ve tried so far:
Held the IF BOOT/RESET button...
Hello,
After I upload a new signed image to my device using MCUboot serial recovery (single image), MCUmgr Img_mgmt_client API
img_mgmt_client_state_read() always fails...
Hi Nordic team,
I am plan to design an IoT sensor that apply to Agriculture,
In case of 2 communications: Near field and far field, I will integration both BLE and Lora...
Hi
Are there any examples of a custom board for nRF54L15?
I have a project built/running on the nRF54L15 DK.
I now want to create a custom board for the nRF54L15.
...
It would be extremely useful to get the HCI Traces (BLE) of my nRF54L15 boards. Documentations: Embedded HCI Tracing For simplicity's sake, here is my setup: - nRF54L15DK...
Hello there,
I'm designing a set of devices composed of a remote and 2 peripheral. The remote's job is to be connected to the 2 peripherals as a central and occasionnaly...
Hello, I’m testing a PID controller for a quadcopter. When I compile the application with the optimize for speed then flash, I notice that the PID response is slower than...
Hi,
I was looking at the .map for my project and I noticed that pstorage.c was taking up a bunch of RAM (~600 bytes), which I thought was a lot, so I went into pstrorage_platform...
The document nRF51422_Evaluation_Kit_User_Guide_v2.0.pdf says:
Locate the Heart Rate demo project found in the folder
ARM\Device\Nordic\nrf51422\Board\pca10003\s310\ble_app_hrs...
I copy static void radio_disable(void) and void radio_tx_carrier(uint8_t txpower, uint8_t mode, uint8_t channel) into my project.
I call radio_tx_carrier(RADIO_TXPOWER_TXPOWER_0dBm...
Hi all,
I have a spurious crash in the softdevice I guess.
It occurs sometimes when the master (an HTC-M8 android phone)
rapidly submits characteristic changes
(acknowledgement...
SDK: V6.0
HW: PCA10001
APP: s110/ble_app_hrs
Question:
If use "twi_master_init()" with "twi_hw_master.c", the current consumption is added 1m
A. But if use with "twi_sw_master...
Hi I am completely new to ARM development world. I have been developing for years for PC.
Now I am working on a Project where we have decided to evaluate nRF51822 chip...
I would like to know if it is possible to use the internal RC oscillator without calibrating every 4s with the softdevice disable. I just want to read a sensor every 2s and...
I'm interested in using BT LE to collect data from a number of serial based devices -- a point-to-multipoint configuration. I'm familiar with the UART examples and have seen...
Hi,
i am searching for infos about my concrete BLE-Sig certification situation but i cannot see the forest because of all the trees :o)
i am currently developing a BLE...
Hi,
I know that a lot of question exists on that subject, but I can't manage to have an accurate battery measure on [Nordic Beacon device] (battery CR1632 3V) ( www.nordicsemi...
Using the nRF Beacons app, but cannot see the battery condition of each beacon. Is this already implemented - if so how to turn on? If not how is it implemented?
Using the nRF Beacons app, but cannot see the battery condition of each beacon. Is this already implemented - if so how to turn on? If not how is it implemented?
Hi,
after reading the nAN-36, I tried to write an application for the nRF51822, with the custom Led Service provided with nAN-36.
I take as a base the Nordic HRM application...
