I was doing development on the development kit and I noticed that when flashing the device there is application core and modem core firmware that is flashed
I'm trying to...
Background
Our device uses the CONFIG_LTE_NETWORK_TIMEOUT option from LTE Link Control, which by default is set to 600 seconds (10 minutes). I haven’t found any specific...
Hello, as the title suggests, I have an issue when powering the nRF9151 DK with an external power supply. Normally, I power through USB, and it's fine. However, when I followed...
Hi all,
I am using and nrf9160, in particular a thingy91. It is running 1.3.7 firmware. I have the SLM sample loaded and can sent AT commands to the device using the nRF...
Hello,
We are working on Zephyr sample app Mesh on nRF52840dongle with nRF Mesh application.
After going through the documentation and few other Q&A on the portal, I was...
Hlo
I have to asked that i am working with custom board of nrf5340 and i want to flash and check the rf signal by flashing through the nrf5340 development board and i am...
Hi all,
I'm encountering an issue with the TWIM30 interface on the nRF54L15 (pins P0.03 - SDA, and P0.04 - SCL), using vanilla Zephyr v4.2.0-rc1.
The setup involves external...
I am working on a project which is currently based on the nRF51922, and I would like to look at the S310 specification document. I found a link on this page: www.nordicsemi...
This is not a real question for support. It's more a success story i'd like to share with you!
Our company develops firmware for various customers on a lot of different...
Hi,
I'm trying to set up an iOS app (which I know is working properly) with a nRF8001 using nRFGo studio. I do not have the nRFGo dev kit (only the 8001 dev kit) so I hooked...
Hi
How to set device address in nRF8001?
I only see get device address command.
Does it mean I just only put my device address in MCU?
Thanks.
BR
Atlas
Hi,
I'm trying to generate some time variant values for testing purposes... rand() always returns 1447534768! This is in the proximity app FWIW.
So, I thought I would...
nrf24le1 memory map shows that there are two sram block size of 512byte ,the first one is data retentive (address 0-0x0200) ,another one is data non retentive (address 0x0200...
My device use the firmware program ble_app_uart to connect the nexus 7 which Installs the nRF UART 2.0 for Android 4.3 。The first connection is ok，and Data sent and received...
Hello,
I am a beginner in the world of bluetooth and bluetooth smart connections. I am working with an nrf51822 Evaluation kit an android phone (Nexus 4 running 4.4.2)...
Is it normal that after cutting SB8 our chip is still working when connected to USB port? (in case of battery we need to connect pin 1 and 2 from P1). I spend long time looking...
I have a custom board that uses the nrf51822. I have been using the sample application ble_app_uart with only one minor change, I use the internal clock (NRF_CLOCK_LFCLKSRC_RC_250_PPM_4000MS_CALIBRATION...
I'm wondering when my firmware changes over time what will happen with information stored with pstorage? For example if I my new firmware release adds an additional pstorage_register...
If I have persistent data that will be updated semi-frequently, will pstorage wear out the flash memory? What steps should I take to be sure my data storage will remain functional...
Hello,
I tested nRF51822 with ble_app_hids_keyboard example, i found it cannot pair with more than one devices.
Procedures:
Pair PCA10001 with iPhone#1, it can...
Hello.
I have a nrf51822 ek and trying to create my software using same technics as the bootloader example from sdk. But sdk's bootloader in my case doesn't work. I programm...
