Hi,
I was looking at the .map for my project and I noticed that pstorage.c was taking up a bunch of RAM (~600 bytes), which I thought was a lot, so I went into pstrorage_platform...
The document nRF51422_Evaluation_Kit_User_Guide_v2.0.pdf says:
Locate the Heart Rate demo project found in the folder
ARM\Device\Nordic\nrf51422\Board\pca10003\s310\ble_app_hrs...
Using the nRF Beacons app, but cannot see the battery condition of each beacon. Is this already implemented - if so how to turn on? If not how is it implemented?
Using the nRF Beacons app, but cannot see the battery condition of each beacon. Is this already implemented - if so how to turn on? If not how is it implemented?
Hi All
I am doing a BLE based project using nRF51822.Where i need to handle the message [with UUID] by using ble_gatts_char_handles_t.
so, can any one please share information...
I have a central application and peripheral application that are based on the multilink-central/multilink-peripheral examples.
I've modified them to run on the PCA10001...
Hi All,
I'm using nRF24L01P for TX device and want to receive packet from nRF51822 RX device.
nRF24L01P TX device Register settings are as follows;
Reg.EN_AA=0x00...
Hi All,
Please Reviwe for a attached circuit file(Chip ANT of nRF51822.pdf).
I also attach a datasheet of chip antenna applied for that circuit(SDBTPTR3015 Data Sheet...
i work with the nrf51 example for ble and sd130 (nrf51 dongle and sniffer) and now i like to use sd310 for ble and ant+. is there also a example for sd310 (or sd110)?
Th...
Hello everyone,
I am using ADC functionality with NRF51822 and its working fine, Interrupt is raising when ever i give input to Analog Pin. Communication protocol i use is...
Hello.
I'm trying to start developing with the nRF51822 Eval kit with Eclipse and ARM GCC but I ran into some problems when trying to run the ble_app_hrs_example. I've been...
I have enabled a gpiote module, it does not set gpiote_enabled to 1.
I have tried deleting the file in the RTE folder with no success. I have tried disabling and enabling...
Hi,
I would like to change the transmission power of the beacon kit so that I can switch back and forth between high and low tx powers for each set of advertising messages...
to me it made sense that EN_AA settings are controlling the receiving pipes if an ACK has to be sent back upon receiving a valid packet.
then i thought that the settings...
Hi,
I'm exploring the ANCS example with SD130 SDK 8.1.0 ...
The application acts as a GATT client to receive notification from GATT server on the iPhone.
I see in the...
Hi everyone, I am now writing a program with scheduler. But the program always can't enter app_sched_execute. I don't kow the reason. Is the scheduler blocked.
Firstly...
Hello,
I'm trying to implement a DFU support into the application, and in order to learn how it works, I'm following the steps at the page developer.nordicsemi.com/......
Is there an easy way to find out the range of handles for a service which I added? Obviously the first one is the service handle, then you add characteristics and descriptors...
Hi,
While access sd_ble_gattc_write api, I got an error code 0x00000011. If I check nordic document for sd_ble_gattc_write error code, I can't find any error code with...
I would like to use nRF2460 in my project (Hearing Aid for elder people).In that I need to transmit the data from a mic/line in to >30 receivers within a range of 100 yards...
I'm using nRF51822 and i want to send a notification to the central to notify it for the changing of a characteristic value (major_value) after using the sd_ble_gatts_value_set...
