According to the nRF51 series reference manual.
10.1.2 Debug interface mode
Debug interface mode is initiated by clocking one clock cycle on SWDCLK with SWDIO=1. Due...
Hi,
I was looking at the .map for my project and I noticed that pstorage.c was taking up a bunch of RAM (~600 bytes), which I thought was a lot, so I went into pstrorage_platform...
The document nRF51422_Evaluation_Kit_User_Guide_v2.0.pdf says:
Locate the Heart Rate demo project found in the folder
ARM\Device\Nordic\nrf51422\Board\pca10003\s310\ble_app_hrs...
Using the nRF Beacons app, but cannot see the battery condition of each beacon. Is this already implemented - if so how to turn on? If not how is it implemented?
Using the nRF Beacons app, but cannot see the battery condition of each beacon. Is this already implemented - if so how to turn on? If not how is it implemented?
Hi All
I am doing a BLE based project using nRF51822.Where i need to handle the message [with UUID] by using ble_gatts_char_handles_t.
so, can any one please share information...
I have a central application and peripheral application that are based on the multilink-central/multilink-peripheral examples.
I've modified them to run on the PCA10001...
Is it possible to do OTA from one nRF51822 to another? Is so how, and is not why?
I am using S120 and S130 for my applications and would like one device to uppgrade another...
Nordic has provided a good SPP implementation over BLE.
devzone.nordicsemi.com/.../
However, will it raise power consumption and cause BLE to lose its low-power characteristics...
When trying to do a direct advertise massage ( sd_ble_gap_adv_start ) I get error code NRF_ERROR_INVALID_STATE (Invalid state, operation disallowed in this state). This is...
Hi Team,
In my application UART is used.
I need to send parity bit based on particular responses that I need to send to the device
connected to UART.
Can I change configuration...
Hello,
I'm working with timeslot API (basing on github.com/.../observer) . I have an advertising and active scanning running concurrently. However, I want to completly...
I am using nRF51822 to generate 3K HZ PWM signal for a buzzer.
I read other people's question and try it.But as far i can't solve this issue.Please help.
At first i use...
Hello,
I just ordered a shiny new nRF Beacon from Mouser. The beacon is version 1.1.0 advertising "DfuTarg", so I am attempting to flash the application file that comes...
Enlight of the increase in 8.0 SD size, I am concerned that my application size may soon grow too large to utilize Dual Bank DFU. I know the actual size of the .Hex files...
修改Device_Name.jpg
After programming, the device name cannot be changed.
Is there any solution that can achieve?
I know that I can change the paramter from the function...
Hi,
I am using the NRF8001 in UART mode and attempting to bond with my android device (Lollipop 5.0 Nexus 6).
i am using the nordic arduino sdk which is found here:...
The Master Control Panel will be able to keep the connection for hours and hours.
But when I am using the iPhone 6 to do the test, after connected, it will also be disconnected...
Hello
I've been having some strange problems with my SPI and TWI bus. In my setup, I'm using SPI0 and TWI1. I noticed that, even though I'm not using it, that SPI1 was...
This seems to be a common problem after searching in this forum. In my case, I need to read from an I2C slave and send the data out in BLE. I have made it work without SoftDevice...
Hello!
In my application, I have to receive UART signals from another device. The problem is the signal comes inverted so the nrf51422 can't handle it. I thought in 2 possibilities...
