Hi,
Parameter uint8_t ble_gap_scan_params_t::filter is present in the documentation, but not implemented.
Checked for SDK 5.2.0 and 6.0.0.
devzone.nordicsemi.com...
After I get a Disconnected() event, I want to start scanning again, therefore try to call StartDeviceDiscovery() again.
IsDeviceDiscoveryOngoing was checked before.
The...
Hi, I wanted to ask a question regarding sending data.
I currently have external memory that will send out serial data (SPI) to the nordic microcontroller. I have saved...
Recently, I try to programme nRF51822 DK communicating with nRF2401e1 DK,unfortunately，which does not success. With setting radio configuration: TXPower,frequency channel...
E:\BLE\work\nrf51_sdk_v6_0_0_43681\nrf51822\Board\nrf6310\s110\ble_app_hids_keyboard
SDK 6.0.0
Softdevice 7.0
When I connect to Android 4.4.3 device(Nexus7 II) will...
E:\BLE\work\nrf51_sdk_v6_0_0_43681\nrf51822\Board\nrf6310\s110\ble_app_hids_keyboard
SDK 6.0.0
Softdevice 7.0
When I connect to Android 4.4.3 device(Nexus7 II) will...
I have been trying to understand and get the “ble_app_template” running this weekend, but I keep running into errors. For example in
static void sys_evt_dispatch(uint32_t...
I have noticed the PWM library in SDK v 8.1 randomly changes polarity of the PWM channels. I can't figure out what causes it to happen... seem's random, but I doubt it.
...
I am trying to upload the blinky example with the s110 softdevice into the nRF-DK board I just bought. The documentation says "flash_softdevice target". But I see no such...
Hello, according to the Product Specification v3.1, the supply voltage range is 1.8 V to 3.6 V.
As you may know, most of the lipo batteries have a nominal voltage of 3.7V...
I am following the NaN-36 example... So far all is going well but i am stuck at section 4.5.4 . I have checked over all the directions three or four times... I have to be...
I am hoping someone can point me in the correct direction as I have posted my question on the SIG forum and didn't receive any responses.
With a nRF51422 device is there...
I've followed the instructions for adding the DFU service to my app to the letter and can see the DFU service from the central and can enable notifications on the control...
Hi.
nrf51x22 has 32 IOs. can we assign 2 pin to usb d+, d-, and listen interrupt.
yes, nrf51x22 has uart support, but many host device only have usb port. serial port...
Hi All,
I am using NRF51822 chip pca10001 development board.
I flashed ble_app_hrs application to the board.
I configure 3 channel for PPI.
static void ppi_init...
Hello all,
I'm writing code for the nRF51 to allow it to be driven via the Android ANT SDK (from Dynastream), using standard ANT protocol messages.
However, it's occured...
Hi,
I'm using the nRF51 DK as a BLE sniffer with your Wireshark plugin. I have several BLE peripherals in the same room I'm testing it so it will be useful to filter data...
Hi, I'm newbie developing with nRF51. I'm working in Firmware for a ble central role that can read all the macs of ble peripherals roles near. I want to event or function...
Hi all,
I've a problem that drives me crazy for some day.
I installed all SDKs, and trying to write some BLE apps. Everything works fine but i cant't find where pstorage_access_wait...
