I am getting get BLE_EVT_USER_MEM_REQUEST and BLE_GAP_EVT_CONN_PARAM_UPDATE event, when writing to ble device, sample code did not handle these event, and seems no document...
Hello:
Why do I erase SDK5.2 version of flash and read not, in SDK4.2 can. I tested nrf51_sdk_v5_2_0_39364\nrf51822\Board\nrf6310\flashwrite_example is a good example.However...
before i write the flash, it has been erased.so ,its value is all 0xff.
when i write 0x00 to flash address 0x0001,the value read out is not 0x00 but 0x01,and the value in...
I'm looking for a way to use the nordic uart service ( devzone.nordicsemi.com/.../ble_sdk_app_nus_eval.html) from Linux using the native Linux BLE Stack (BlueZ). My application...
Hi,
I've created an application using the S110 experimental ANCS demo. I successfully implemented ANCS and then began to structure my application around it. At some point...
Hello,
In an ongoing company project we use a couple of nRF51 transceivers forming a beacon enabled wireless sensor network consisting of one base station and multiple...
I want to count clocks in order to implement a watch. I use the RTC0 as my time-base and count mainly with this device. As it has just 24 bits it would not last for long,...
Hello,
I am working with S130 softdevice. I am using SDK v6. I want to send multiple data as a single characteristic value (possibly as a structure). But it is seen that...
I'm playing with open-source IoT over Bluetooth and recently was told about TI's new SensorTag product line which uses a CC2650 multi-sensor bluetooth base platform with pluggable...
Hello, I am tryong to use to masters to communicate with two accelerometers.
Q1_ I found the following image from Nordic's website that shows SPI0 pins but there is no indication...
I'm having a weird issue where the stock sdk 8.1.0 DFU software is not timing out properly and getting stuck in the bootloader, advertising dfuTarg forever.
Our iOS app...
In the nrf51 series reference manual section 12.1.9 it states that there is hardware protection that prevents write instructions from being executed and that there is more...
I want to add a battery level characteristics to a custom service. Here is my approach:
In main.c, I add a timer to update battery level periodically
void data_update_timer_timeout_handler...
So I've been having issues with my debuggers where occasionally Keil will crash and I won't be able to reconnect to the debugger interface without a power cycle (might be...
Hi, My project is that when a button is pressed on a slave (nrf51822ek), a central (another nrf51822) gets to know which slave has triggered and sends its status 1/0 to a...
Hello,
I am using ISP130301-Development Kit 1 for nRF51822 from insightsip.com which consists of postimg.org/.../
There is used a button on PCA10028 for deleting bonds...
Hello, every:
I have success to use sd_ecb_block function to encryption data. But I am not find how use this function to do decryption. Please teach me how to use this function...
I am trying to perform a simple ADC measurement using polling rather than using an interrupt. I have looked at examples and read the ADC section in the reference manual, but...
Hi Team,
Is there any way to enable/disable all interrupts?
Will BLE connection get disconnected because of this? If yes the what are the possible ways to
maintain the...
Hi,
I am new to all this,
I have just started using the nRF51822 evaluation kit.
I have manged to run the blinky example, however, eventhough I managed to download the...
After implement PWM (using pwm example at nRF51_SDK_8.0.0\examples\peripheral) into my BLE based nRF51422 project using SoftDevice S110, it has been working fine; however...
I want to add a command ordering by uart to make MCU entering Bootloader mode in app.
To achieve this function, I plan to use the two following example in SDK 8.0
ex1...
