Hi We are working on setting up CI/CD pipelines for our nRF application. The application is set up as a stand-alone application with its own west workspace. It uses external...
Hi ,
1.In the example: In nRF5_SDK_17.1.0_ddde560_usbd_msc_1\components\libraries\block_dev\qspi\nrf_block_dev_qspi.c, I need to set the following 0xB7 bytes. How should...
Hi I'm testing the current consumption of the external qspi-flash on nrf5340dk [ MX25R6435F]. I have used ppk 2 to measure consumption with the dk and also have used a power...
During the development of a Matter over Thread product, I encountered the following issue:
After adding two Matter over Thread devices (an OnOff Switch and an OnOff Light...
Hi Nordic Teams :
I would like to check the current consumption by BLE DTM.
1. Is the table measurement is from 3.0V input?
2. I find the condition in the datasheet...
HI ALL,
nrf54l15dk,v2.8.0,peripheral_uart demo and no changes have been made.
Then add the following content to prj.conf
sysbuild.conf
mcuboot.conf
At this...
I'm developing my application with nrf 52832 and nrf SDK v17.
I know NCS is more powerful. I'm currently learning how to use it.
But now.I still need my application with...
Hi,
I am using nRF51422 with s130 soft device along with SDK v9.0. I am trying to read/write flash memory using pstorage module. I am using BLE nus service for data transfer...
each time I start my program (nrf51 device) I get an error code I save in flash to check it at next restart. I can read error code 0x20
is this a correct error code and what...
Hi,
I try to generate a PWM signal on PCA10040 with the nRF52832. To do that I copied the code from the Product Specification into my application, but nothing comes out....
Hi,
I made my prototype board using the nrf51822 chip. for this prototype i use an on-board connector + external programmer to flash the nrf51822 chip.
that's work...
I am looking ahead to the time when I will graduate from using the nRF52 development board to building a custom device with the SoC. The PCA10036 chip will obviously not be...
Hello,
I am almost finishing developement of a BLE module using nrf51822.
For mass production, I hope I can program Softdevice/Bootloader/Firmware to 10 nrf51822 using...
Hi
I want to receive and send a lot of data in a short time (connection Intervall is set to 20ms). And I get the App-Error 0x3004.
I found this definition for the error...
Hello,
I am currently trying to figure out a problem with my mesh. If I stop the event handling of one node, other nodes in the network will fail to send data from this...
PAN #9 in the nRF51822-PAN-v2.4 document provides a workaround for non-functional OUTINIT. This question and this one improve the workaround and state it's unnecessary in...
We have used the first version of the S132 softdevice with the Engineering A version of the nrf52 chip. Now with the newer Engineering B version, we have moved to the second...
Hello Everyone,
i am trying to simulate the circuit using Proteus so can anyone tell me where can i find the Pspice model files for the Nrf51EVB is it available? any suggestions...
Hello to everyone.
I write code for NRF24LE1 using KEIL and rtx tiny. But i have some problems.
When i power on my device, programm don't run correctly, but when hard...
Hi experts,
The softdevice is s120. I get error code BLE_ERROR_NO_TX_BUFFERS after calling sd_ble_gattc_write() several times. I want to ask what does the tx buffer mean...
I have a strange problem on my target nRF51822. When I try and use the UART interface between my nRF51 and my host MCU, it causes the nRF51 to reset and the RTT terminal to...
