i am writing data from wav file to w25q128jv and i got error -22 at some offset while writing. i tried many config but it seems the problem is not solved, does anyone have...
Hello Nordic Team,
I am currently working with the nRF54L15 DK and interfacing an occupancy sensor over UART. In my standalone application (non-Matter), the UART communication...
this my yaml.file to use partition manager, beacause iam implementing DFU, USB MSC with fatfs in single project
fatfs_storage :
address : 0x00000000
size : 0x00200000...
i am working on custom board nRF52840 with display ST7789 + touch Ft6336
1) i want to use LVGL library with Display how do i get started with LVGL .Any tutorials or sample...
Hello,
I higly need to run twister unit tests in debug mode with breakpoints, step by step, spies and other debug tools in vscode. I did not find a way to do so.
Is...
Hello, this is probably a very beginner question but I don't know how to configure interrupt for the GPIO headers on the nRF52840 dev kit. I tried to search in this forum...
Hello,
I'm looking for answers and some explanation for two main questions - is it possible to perform non-simultaneous multi-image FOTA over WiFi? Is it possible to support...
I am getting device id of peripheral on central and then getting it displayed on hypertermianl hyperterminal using ble app multilink perihperal code with multilink central...
Hi Everyone,
I have what I hope is a simple questions. I am creating a piece of hardware that will act as the peripheral to a central iOS app in regards to a standard BLE...
Is there any construction available in the SDK, to achieve printing functions, with an undefined number of parameters ? The classic example :
#ifdef CONFIG_DEBUG
#define...
Hello,
I've ready the final S130 spefication and it states that the advertiser is started as early as possible and that i runs asynchronously to all other roles. Now I...
Calling app_sched_event_put() from the NRF_RADIO_CALLBACK_SIGNAL_TYPE_START signal handler causes a crash due to the CRITICAL_REGION_ENTER() call inside of app_sched_event_put...
is there any code for device which act as master and peripheral other than nRF51_SDK_8.1.0_b6ed55fnnn\examples\ble_central_and_peripheral\experimental \app_s130_demo\pca10028...
I have a simple nRF51822 BLE application where a voltage is read by ADC periodically, and several values are sampled and averaged. However, from time to time, I get another...
Hello All ,
I am working on nrf51822 with sdk 7.1.0 and softdevice 7.1.0 .Earlier my ble connection was working very good with no disconnection anytime unless i disconnect...
Now I'm working with MCP 3.9.0.
When any device is connected, characteristic default values are not 0's. Can they be initialized in any way? It is a little bit annoying when...
Is there a separate reference resign for the 1.8V of operation (as in case of nrf51)? Or it's implicit and the chip can be powered in range of 1.7V - 3.6V.
Thank you!
I am using nrf51442 as central client.
I have used
SDK\v7.1.0\examples\ble_central\ble_app_hrs_c\pca10028\s120\arm\ble_app_hrs_c_s120_pca10028.uvproj" as a atart point...
Hi All,
I am integrating Johanson's balun and Nordic's L shaped pcb antenna, is it possible to have the antenna connected directly to the balun's pad? as in the below pcb...
The m_client_count is like instantly increased when I power up another (or the first) peripheral.
But with increasing connection interval the time till the central finally...
Hello,
i want to implement DFU with the S130. The problem is, that I currently do not use the device manager because I need both Central and Peripheral connections at the...
Hello,
This is an add-on question to the the one outlined in:
devzone.nordicsemi.com/.../
That question states that:
The maximum SoftDevice size that can be updated...
