i set up an coap/iot environment and but i was getting error while compiling code for adc i followed steps from this post devzone.nordicsemi.com/.../ here is the problem
Hi all,
I've developed a broadband vibration energy harvester that is able to pick up uW of energy from just a couple Hz all the way to 150Hz. I'm currently looking for...
We use SDK12.10 Main.c (d:\nordic\5142xx\software\org-sdk12.1\nrf5_sdk_12.1.0_0d23e2a\examples\ble_central_and_peripheral\experimental\ble_app_hrs_rscs_relay.
My question...
Solved: Well, turns out delay and SCK doesnt work well together haha. I imagined the sck signal to be a background thread of some sort. I was wrong.
Hi guys,
at the...
Hi
Im looking for a developer in Denmark to discuss ble technology with. Im trying to get better to understand the technology, because i have some ideas involving beacons...
This system does not work if I enable the third Pipe (Pipe2) .
The system is working without any problem as one RX and two TX (Pipe0 and Pipe1).
The problem on enabling...
Hello,
i have read if not all posts about writing to FLASH while using BLE. But could not find the desirable method.
What i would like to do is to write to flash from...
hi all:
Recently, I use nrf51822 as a central to connect some older sensor, but the ble chip of the older sensor did not use nordic, so I have this problem. I develop the...
I have the Heart Rate Service(HRS) program written in embedded c. I connected a two LEDs to nrf51822 board. One LED will start blinking when advertisement starts and other...
How do I write a value to gpregret when flashing the chip?
Basically, what I need to do is be able to detect the first time the chip is powered on so I can go into a special...
In my device I want to adjust the slave latency connection parameter, however my desired min-max connection parameters are the same as during the initial connection. I find...
I have an imuduino (arduino board with nrf8001 bluetooth and some sensors) board and am trying to load some of the profiles from the nordic arduino nrf8001 bluetooth api on...
Hello
I made the switch from SDK 6.0.0 to SDK 6.1.0 with SD7. At first we didn't get it to work. We would get the error NRF_ERROR_INVALID_PARAM on dm_init(). The problem...
Hello, I set up the environment by This . Now I can ping the device on the raspberry pi.
How ever, When I run the python client example on My ubuntu-14.04 and try to connect...
Hi, where can I get access to the definition and meaning and definition of the built in functions and headers of nrf51822? for instance what does this mean: uint8_t err_code...
Hi ,
I am using nRF6.0.0, SoftDevice 7.0, for nRF 6310 hardware.
I am trying to develop a ble keyboard app with the help of Ble Keyboard Sample we have in the SDK. As...
HI,
I am currently working on a project to develop firmware for S110 nRF51822 softdevice .
Currently I have a device with the following details: Ic Version - 2, Variant...
Hello, I am trying to make adc sampling on two adc inputs at the same time. The adc example (simulataneous-adc-sampling-from-two-inputs) is not using IRQ handler and applying...
Can i flash the stack S310 in any nRF51822?
I have a NRF51822 QFAAG0 but I cant run the example ble_ant_app_hrm properly.
I use Keil MDK5 and nRF51 SDK 5.1.
Thanks...
Which works better:
a single GATT characteristic using 'write without response' for transmission from the central to the nRF51822/S110 peripheral and 'notifications...
Hello everybody,
I searched the forums and saw numerous questions regarding sampling multiple ADCs but none for this exact use case.
The question is simple - is it possible...
Setup: Galaxy S3 (Android 5.1.1), nRF52 with S132
Basically I am trying to estimate distance from the phone on the nRF52 by measuring the RSSI and in order to do this to...
