Hi,
I'm programming the nRF51822 and save some user data into the FLASH by using pstorage_update . It works fine if I set system off mode, and wake it up. I can read back...
Hi,
I have been using nRF51822 with my Android app using Android's Bluetooth Low-Energy APIs.
In order to get more details, I am currently working on integrating the Android...
I'm looking at interfacing a typical Wheatstone bridge sensor to the nRF51822 ADC. This particular sensor only requires a mA or two for excitation and the output fits within...
When use the "nRFBeacons" app to update the info on my beacon the following happens:
Go to update tab.
Select "Connect"
Press "SW2" on beacon and see the LED begin flashing...
I am using s110 and nrf51822. I've set up up a long characteristic of 154 bytes.
Sending between 1 and 154 bytes works as expected.
Sending 155 - 160 bytes gets rejected...
Hi,
I tested the nrf beacon application, it allows only the beacons with company identifier 0x0059 (nordic's id). But i need to modify it to support all the device, how...
I use a app_timer_create() function to create a task(200ms once)
when in the task_timeout_handle() ,
I do something more than 200ms,
what will this timer going ?
Hi, I'm planning to create a custom PCB that uses nRF52832-QFAA.
Currently, I chose the Q22FA12800025 32MHz crystal to use, which is the same one in the PCA10040, I believe...
Hi,
I use nRF51822 with 256k flash and external sensor, and i want to write the data i receive from it via SPI to internal flash?
After the data received i want to send...
I've seen a few posts in regards to the usage of MCP in a windows virtual machine. From what I can gather, this setup just will not work, however I haven't really seen an...
Hello:
I was wondering about the random addresses programmed into the FICR on some of the devboards that I have. I read the devzone and it appears that the DEVICEADDR is...
I read that the DEVICEADDR is always in the advertising packet, so i need to take these data from the master each time that a slave is conected to them. I trying do something...
I'm using nRF52+SDK11.0.0+s132. In the ble_hrs PCA10040 example, the following are defined:
BLE_STACK_SUPPORT_REQD
BOARD_PCA10040
NRF52_PAN_12
NRF52_PAN_15
NRF52_PAN_20...
Similar to the thread posted here , I am trying to merge SD+bootloader+application and flash this to a nrf52 using the Segger programmer. This saves us a huge amount of time...
What is the best way to start a new nRF52 project, on a custom PCB?
I have a custom PCB, with nRF52 module. I use IAR, with ST-LINK V2
Say to test the GPIOs, do I start...
I took a look into the PCA10040 and the differences from PCA10036, seems to be minimal...
NFC connector and some breaking points. My question is: if somebody from Nordic...
Hi,
I am new to the nrf52. I want to implement the code that gives me current date and time value based on default set values.
for this i need to read the current counter...
Hi
Any ideas how best to implement a combined iBeacon and standard advertising device (both devices are active at the same time) ?
The iBeacon has to send an advertisement...
Is there a way to generate a DFU OTA image from OS X natively without having to use a Windows platform? It seems that the missing step is dat file generation and json manifest...
Hello guys,
Firstly, i would like to apologize if this post doesnt belong here. But i couldnt find any other platforms anywhere else for me to ask this question. So i have...
hi .
i did what this linke says
but it get me these error
..\main.c(632): error: #20: identifier "NRF_CLOCK_LFCLKSRC_RC_250_PPM_TEMP_8000MS_CALIBRATION" is undefined...
