Hi!
With the release of NCS 3.0.1, the required SEGGER JLink version to v8.18. pynrfjrprog is bundled with SEGGER JLink v7.94. From your website, it seems nrfjprog, being...
In my project (SDK 2.9.1), I have configured a USB Mass Storage (MSC) device that uses a QSPI flash, like the one on the 52840DK board.
My system goes into sleep mode...
Hello,
Over the past three days (up until today), we've observed inaccurate behavior in the Message Routing Service. Specifically, we shut down our destination service during...
Hello Nordic team,
After many hours I have not been able to get socket dispatching working with Zephyrs MQTT client, and I am not sure how to proceed.
First of all I would...
Using latest SDK and toolchain 3.0.1, VSCode and nRF Connection Pack on Windows 11 I nearly never see a working nRF Kconfig GUI - only the first time directly after I had...
I noticed that in the hid_mouse sample, the whitelist advertising was used to achieve seamless recovery of accidentally disconnected connections.
This function is implemented...
Hi everyone, I'm a beginner in Nordic development and currently learning how to work with BLE and Zephyr (NCS 2.9).
I'm using an nRF52840 Dongle as a peripheral and an nRF5340...
Hello!
I'm looking to build an application on nrf52840 DK that collects multiple sensor values and transmits it over Bluetooth. For now, I don't have a bluetooth application...
Hey I'm doing some SPI transfer in response to a GPIOTE in event. I'm targeting the NRF52840 and kind of went with the following answer:
https://devzone.nordicsemi.com...
Hello,
My setup is pca10040, sdk 14.2, s132.
I have tried firstly the blocking mode function and it is not reacting. After that I used SAADC module in a non blocking mode...
Is it possible to use the mbr, currently inside the softdevice, without the softdevice? Can we use the combination MBR/Application/bootloader? So we have a lot more flash...
I'm developing for the NRF52 DK (nRF52832) using VisualGDB (which uses SDK v11.0.0).
When completed my program is supposed to read data from sensor (via I2C), store it in...
Hello ,
is the NRF52810 surpport LE long range? is the mainstream mobile phone surppot LE long range? if i set the nrf52810/nrf52840 to be LE long range mode, and then ...
I am developing a product for indoor positioning and some thing else.
I want to know that how many beacon device can operate in same place.
As I know, beacon devices can...
All,
I already run BottonlessDFU example successfully after refer to below link. What's more, I added BAS and DIS service to Bottonless DFU example, and after use nrfutil...
Hello,
I found out that S/N from nrfjprog -i command returns the same number among different debuggers, all of them are 123456. At the same time, S/N showing from J-Link...
Hi,
I'm developing a peripheral that expose the HTS service.
I have the on_hts_evt event handler to handle BLE_HTS_EVT_INDICATION_ENABLED and BLE_HTS_EVT_INDICATION_DISABLED...
I am hoping to get solid verification that nordic offers a solution for sniffing BLE 4.2 packets.
The application I need to sniff is maxing out the MTU (250B payload) so...
i want to implement 2 hardware SPI communication in my code. i have one already working. talking with LCD ILI9341. the functions are using spi_write / nrf_drv_spi_transfer...
Our beacons are going into production, and to make function tests faster for our manufacturer we would like to transmit our beacon UUID, major, minor at a rate of 760ms for...
