Close Bluetooth in Iphone's settings when IOS/51822 is paired and connected normally.
several seconds later, Open Bluetooth in the settings again, and observe the settings...
Hi,
I am trying to power off and/or disable a RR[0] with no success.
I am Powering OFF the watchdog in main and then successfully POWERing ON in wdt_init but then I...
Is it possible when using the S110 softdevice to limit the maximum number of packets per connection event? I would like to reduce the maximum amount of time the CPU spends...
I am using nRF51422 Evaluation Kit with the latest silicon revision which comes with programmable softdevice. The kit also contains an ANT USB-m dongle. I have followed the...
I tried to do send & receive binary data from bluetooth in ios app.
But i only can send & receive string or ASCII code data in my app, do you have any method or idea can...
Hi,
I tried ble_app_hids_mouse with Android 4.4.2, it can work properly for first time connection. However, it cannot be re-connected after switching Phone's Bluetooth...
I have installed Keil MKD-Lite V 5.10.0.0 and the Segger software (which linked to the Keil IDE). I have tried to install the nRF51 SDK (5 times) and every time iI get the...
Hello, we've a nRF9161 DK board a we saw on the back side a footprint for mounting an SD card holder and we found the SD card holder component in the BOM.
Unfortunately...
Hi,
I'm getting the following error over and over again from the nrf connect plugin in VSCode:
[west]: FATAL ERROR: failed manifest import in bsim (tools/bsim): [west...
Hello, I am developing my custom board using Thingy53 as a reference design. I am trying to achieve DFU from application using external flash for the secondary image and upload...
Hardware Setup:
Boar d: custom board using nrf5340dk_nrf5340_cpuapp
N CS Version: v3. 0.1 (upgrade d from v2. 4 where it was working)
Problem Description: After...
Hi,
I am wanting to talk to this external 1Mbit RAM chip through an SPI interface: https://www.microchip.com/en-us/product/23lc1024 with the nRF5340 device. Preferably,...
Hi,
I am trying to use the clangd extension with nRF Connect SDK, as it does a much better job than intellisense. I added
set (CMAKE_EXPORT_COMPILE_COMMANDS ON )
...
Hi, we are developping a medical device that receives an audio stream from a smartphone. We have a custom board connected to a different DSP than the one in the nrf5340_audio_DK...
Hi,
I have autoprovisioned and autoconfigured my nrf52840 board (provisioning and configuring are made inside the software and not through external app/provisioner).
In...
I have read info somewhere which said there is method to crack the protection just by setting UICR APPPROTECT register.
I want to know if Nordic has upgraded the protection...
Hello,
I'm developing my custom sensor application. It's a matter over thread device. Before final product I'm working on a NRF52840 DK PCA 100056 v3.0.1 and NCS 3.02. It...
Hi! We're testing nRF7002 with the nRF7002-DK and NCS v3.0.2. CONFIG_NET_ZPERF=y has been added to the nrf/samples/wifi/shell/prj.conf, the rest is untouched. Running that...
Dear devzone, Can our nRF52840 detect 20 nanosecond voltage fluctuations using COMP? For example, if I set a lower threshold of 20mV and an upper threshold of 60mV, and the...
I'm writing an application for the nRF54L15 that periodically receives the local time via bluetooth and keeps track of time on its own between syncs. I'm using a 10ppm external...
Hi，everyone:
We are developing a Nearby protocol combined with UWB, which needs to communicate with the Bluetooth of Apple phones and then use UWB to measure distance. We...
