I'm having some trouble successfully entering ON,IDLE mode. I have pared-down my application to do the following:
Initializes the app_timer using the scheduler:
...
I want to control GPIO toggle by PPI. Timer1 is in timer mode. CC[0] is 1000, and CC[1] is 8000.
I use compare[0] to toggle gpio18 by PPI. I also want to use compare[1] to...
Hi,
I use two evk board to connected and test the uart serialization sample(ble_s110_serialization), one is ble_app_hrs and one is ble_app_connectivity. But I have one...
I am getting get BLE_EVT_USER_MEM_REQUEST and BLE_GAP_EVT_CONN_PARAM_UPDATE event, when writing to ble device, sample code did not handle these event, and seems no document...
Hello:
Why do I erase SDK5.2 version of flash and read not, in SDK4.2 can. I tested nrf51_sdk_v5_2_0_39364\nrf51822\Board\nrf6310\flashwrite_example is a good example.However...
before i write the flash, it has been erased.so ,its value is all 0xff.
when i write 0x00 to flash address 0x0001,the value read out is not 0x00 but 0x01,and the value in...
Hi everyone,
I am trying to advertise data from nrf52832 to a smartphone (nRF Connect).
Below are my advertising parameters.
ble_adv_modes_config_t options = {0};...
Hi,
What is the max timer frequency that the nrf52840 can handle in counter mode?
I see that the timer runs at max 16Mhz when in timer mode, is it possible to get 32Mhz...
Ok I’m new to ARM / Nordic and Bluetooth but after a bunch of reading I downloaded SES and the Mesh SDK and got the light switch demo to both compile and run on a few boards...
I'm looking for where the compiler is for the nRF52832....
I just need to compile code, and copy the binary to the device....do you have any pages which show, step by...
hai. I got thingy 52 from Nordic tech tour. now i would like to reconfigure it. for enabling all its sensor into RTOS(real-time operating system apache mynewt) with the nrf52...
I want to implement a ready line for SPI and I noticed nordic has similar code in your sdk: components/serialization/common/transport/ser_phy/ser_phy_spi_slave.c.
However...
Hi,
I am trying to send data to server using ESP8266 WiFi module interface with nRF52832 DK board via UART interface. My problem is when i sent AT command to ESP8266 it...
Hi,
I have a project with 52810, I met below build error when compiling dfu project:
.\_build\nrf52832_xxaa_s132.axf: Error: L6366E: uECC.c.o attributes are not compatible...
Hi
Now I'm using nRF52810 base on SDK v14.1 and I want to do the OTA for it. When I combile the bootloader project, I get so many error "No space in execution regions....
I just want to change the Advertising interval min and max values in ble_gap.h file in meta wear RG
so do I have to change firmware code or is there any other way to deal...
In the eclipse setup here
https://devzone.nordicsemi.com/tutorials/b/getting-started/posts/development-with-gcc-and-eclipse
It give two links to example eclipse projects...
I can see that we can use APPROTECT to disable reading of the flash.
This seems to be reversible using: nrfjprog -f NRF52 --recover, which will erase the flash and allow...
I used SDK nRF5_SDK_14.1.0_1dda907.
I added cycling speed and cadence service of BLE and bicycle speed and cadence of ANT+ in ble_ant_app_hrm example of multiprotocol. ...
First - thanks to those who answered my question about the Segger Embedded Studio code size limit. It appears to have be fixed when I switch the build configuration from ...
