Hi,
I'm attempting to obtain sensor values for a project to be completed less than a week from now and I have not yet started programming so any help would be greatly appreciated...
Hi
I am using nrf52832,SDK version: SDK : RF5_SDK_17.0.2 .
USE CASE:We have two central and one peripheral.We need to control two central with one peripheral(REMOTE...
Hello,
I am facing an issue with SPI when the SoftDevice S132 is enabled and i cannot figure out what the problem is.
The following test works perfectly when SoftDevice...
Hello!
So I can connect, disconnect and write to my applications characteristics via a PyQt5 GUI I threw together. On the python backend, I use Bleak to
search for devices...
Hi, I am developing using nrf52832 and st7735s.
Successfully displayed the lcd screen using the code in \examples\peripheral\gfx
However, when screen clear, text_8print...
Dear friend I checked the data sheet of 52820 and I didn't see any LPCOMP peripherals. Check the data sheet of 52832, there are LPCOMP peripherals. Comparing COMP and LPCOMP...
Hello,
To finaly adjust the inside crystal capacitor at the end of production, I need measure the LFXO and HFXO frequencies signals to fine tuning. How should I do ?
Best...
Hi Nordic DevZone !
I'm facing an issue that I cannot manage to fix by myself.
So here is the brief: I'm trying to create a BLE beacon that will send some analysis results...
We are working with the nRF7002-DK board and need to measure and minimize power consumption. We are using Wi-Fi in our application and currently working with the sample nrf...
Hi,
I want to measure the current draw of the MCU only on the nRF52840DK while I am running my custom code. I want to exclude the current draw of all components except for...
Hi,
I’m currently working with the nRF52833 together with the nRF21540 Front-End Module (FEM). I have configured the FEM to provide a gain of 10 dBm. I have a few questions...
Custom PCB with nrf5340/nrf7002. Currently was using NCS2.9.0, with WPA2-PSK connection to the wifi.
While trying to enable use of WPA2-Enterprise, I updated to NCS3.0.0...
I want to use Nordic 52840 DK (Bulb FW) as DUT to setup Matter Certification test.
I have completed below steps:
1. Flash Raspberry Pi (Ubuntu Server 24.04.2 LTS (64-bit...
Hello. Right now, I am connecting an external flash using SPI. The external flash is used for firmware updates. I'm trying to launch sQSPI to access the external flash. I...
Hi,
does the Azure functionality in the nrf connect SDK support the SAS authentication? I need to connect only with the SAS key, and as far as I can see, that's not possible...
We are currently working on a project using the Nordic nRF5340 and nRF7002 DK, which includes 1MB of internal flash and 2MB of external SPI flash. Our application codebase...
Hi Q&A My keyboard chip is NRF52832, and the program uses ESB 2.4G communication. The receiver dongle uses NRF52833. Now there is a problem that when the CAPSLOCK is clicked...
Dear All,
In our company, we have replaced the NRF52811 (ublox module) with NRF54L15 (raytac module) for new batches of products.
The fw is a simple BLE to UART bridge...
I am using 2.9.1 toolchain and sdk with a custom nrf5340 board and trying to use High Voltage (HV) with DC-DC mode. I don't know much about it as I have been using a nrf5340...
Hi everyone, I'm a beginner in Nordic development and currently learning how to work with BLE and Zephyr (NCS 2.9).
I'm using an nRF52840 Dongle as a peripheral and an nRF5340...