Hi all,
I’m Bruce — first-time poster but have been working with the nRF9160 on and off for a while now, mainly in outdoor, power-constrained telemetry and monitoring applications...
I have a simple GATT server application with two characteristics, RX and TX. In my prj.conf, I am trying to disable pairing as follows :
I can connect to the server from...
Hello,
I am trying to use LTE connectivity on a custom board with a nRF9160 SICA B1, but i am facing issues with the modem.
With both my own app firmware and the sample...
I have searched all responses here and whatever sources I can find, but not have any success. The main problem is that existing materials appear incompatible with the 54L...
Hi, I have test the throughput using two nRF54L15 DKs and make them close to each other.
My result is:
1. My first question would be: the best througput for 2M phy is...
Hi,
We're working on a project using the nRF5340, where we interface an external NAND flash (4096 blocks) to store high-volume sensor data. We are planning to maintain an...
Hi,
We are currently evaluating the NRF9151 for asset tracking using the AT firmware on the NRF9151 evk and an external MCU for the application firmware, emulating the final...
Hi,
1. After studying about power profiling and application examples/ble_peripheral/ble_app_pwr_profiling, came to know that this example currently supports advertising...
Hi,
I am establishing a Bluetooth mesh network with nordic boards (nRF52 DK) having one provisioner and many provisionee devices. But I have one doubt, if I remove the...
Hello,
We are developing wearable which has NRF52 as main MCU. We are looking for suggestions to select proper sensors like Pedometer, Heart Rate Sensor and 128x32 OLED...
Device：Nrf51822
SDK：SDK12.3
Device name consists of "scanner:" and four digits。But sometimes the device name display error。An extra character appears in the device name...
Hi,
I've undertaken my very first custom Bluetooth PCB project, choosing an nRF52810 as the MCU of choice.
Having already tried and tested a SparkFun nRF52832 breakout...
Hi all!
Antenna that used in nRf51822 developement kit:
too big for my design, so I tried to use antenna that I copied from TI AN430:
There is devices that use...
Hi,
I am following procedure to configure mosquitto using this link http://infocenter.nordicsemi.com/index.jsp?topic=%2Fcom.nordic.infocenter.sdk5.v15.0.0%2Fiot_sdk_user_guides_mosquitto...
Hello,
I'm working in a bootloader based on the one included with SDK15. I want to add a timer that fires every 50 ms to keep track of time. The purpose of this timer is...
Hello everyone,
I'm new to embedded system and I'm working with the NRF52 and more precisely with the DW1001 (NRF52 + DW1000).
The Decawave device (DW1000) is already...
Hello,
I am trying to run a simple ble_app_hrs example from the SDK v12, but I am getting the same error as in this post devzone.nordicsemi.com/.../
Building ‘ble_app_hrs_pca10040_s132...
Hi,
UART and UARTE are specified in data sheet. these are separate UART or one UART and configured bt software. Please explain.
Thanks and Regards,
Harikant
So literally, I cannot trust what IAR is doing. Running version 8.22.1, it crashes every time I attempt to debug an nRF52832 device (SparkFun board).
I've already programmed...
i'm using uart for debugging, works fine and dandy except when in app_error_handler.
There only the first character is being printed before we go into an infinite loop. Inside...
Hello,
My custom board is based on an accelerometer which sends interrupts to nrf52832 to Sleep and Wake-up (pins GPIOTE).
(The FW is based on SDK15\examples\ble_peripheral...
Hi!
I am using SDK15.
I am using ble_app_uart and let's suppose that both of my characteristics (RX and TX) have char_md.char_props.write = 1; property so I am able to...
