Using one ADC, the current can be reduced to about 40uA after the ADC value is taken. Using a two-channel ADC, after the ADC value is taken, the current stops at about 0.4...
I'm searching for a software engineer who can help us getting OTA support between nRF52810 and PIC16 MCU.
nRF52810 must have command- and data mode over UART, Pic controler...
I want to be able to read the gyro and accelerometer values from the MPU6050 sensor.
As a base start I downloaded the NRF5 SDK V15.3.0 and modified twi_sensor_pca10056 program...
Hi. I'm using nRF52832, SDK13.0.0.
I should use SHA256 and MD5.
I made my code as below.
NRF_CRYPTO_HASH_CREATE(init_packet_hash, SHA256); NRF_CRYPTO_HASH_CREATE(init_packet_md5...
Hi. I'm using nRF52832, SDK13.0.0.
I want to use SHA256 as below.
output32Byte = SHA256[input32Byte];
Which function or example can I refer to?
And also I want to...
I tried to port the example "ble_app_ipsp_initiator" to pc-ble-driver and run on Linux. The peer device is another PCA10056 device running ble_app_ipsp_acceptor. The problem...
hi...
i want to use two uarts in nRF52840 , one uart to one pc and another uart to another pc .Data should be transferred and received between the nRF52840 and pc how can...
I added a new model to light_switch/server project according this , but how to test it working successfully or not?
I have tried to modify the light_switch/client to accept...
Hi，
When i do as the document say, i download the firmware to the development kit, and then i don't know which pin is the Tx and the Rx. How can i do all the function test...
Hello, I bought nRF51dk (pca10028) a year ago it was working fine last year in Segger Development Studio, now it gives build error "core_cm0.h: No such file or directory"...
Hi guys, me again.
Thanks for all the help before. I was developing me code with the example uart and now would like to control a LED with PWM output.
I have went through...
Is there a way around the issue where bluetooth communication acting as a pass-though terminates the packet whenever null character is found in the packet.
SDK: nRF5_SDK_12...
Hi,
I'm using the evaluation board PCA10040 with Segger Embedded Studio. It stopped working well and I get erroneous services even with the supplied examples (ble_app_blinky...
The device is broadcasting as "DfuTarg" and i want it to come out of the bootloader mode back to the application mode. Is there is a command i can issue to Secure DFU Characteristic...
Hi,
I'm modifying files in the NRF5_SDK_14.2 distribution and it is not clear to me which ones are part of the core SoftDevice libraries (and I, therefore, should not change...
(I know it has been asked before, but I thought I'd check in again..)
Has anyone had any success implementing the Dallas one-wire protocol on the NRF51822 - in particular...
Hello,
I imagine this is a pretty common and basic question but I couldn't find anything online.
Since the nRF52xxx chips are single-band 2.4GHz (and possibly sub-GHz...
I'm having trouble writing to a gatt characteristic using the python bindings for pc-ble-driver
Service discovery works fine, I managed to connect to a BLE server and reading...
I have a device that I need to control, that needs 2 different square wave signals of different frequencies (although they may be multiples of each other), one at around 4...
Hi all. I try to run capacitive sensor example on nRF52832 with my hand made capacitive sensor which I made according to this tutorial devzone.nordicsemi.com/.../.I connected...
Hello,
When i execute a function that uses TWI from a timer handler the NRF gets stuck.
I assumed that this issue occurs because of interrupt priority so i gave the TWI...
