As the tittle,can anyone tell me how to save data to the flash with nRF51822 ? I use SDK9.0.0 and S110. before I turn off my machine, I want to save several parameters to...
I use example from SDK 13 ble_app_uart_c.
I changed uuid to my uuid from nrf51 peripherial device. I get event BLE_GAP_EVT_CONNECTED
where made
err_code = ble_db_discovery_start...
dear all,
i need your help.
Where we are:
We use mbed software developer platform.
We have BLE Nano V1.5 + MK20 USB Board V1.0 from RedBear.
We are able to generate...
Hi:
environment:
target board: DK52 board and run LWM2M example of IOT-SDK v0.9
router: ubuntu 16.04 on VM and runs bsserver and LWM2M server on ubuntu 16.04 ...
Hi,
I'm interfacing a nrf51822 and a H8/3294. My question is how much can I drain a the txd pin of the H8/3294. That means my question isn't really about nrf51822.
In documentation...
Hi,
On the 3.30 of nRF52832_Rev_1_Errata_v1.5.pdf, the sleep current with LFXO active is 0.5ÎĽA higher.
I am using a nRF52832 module with the low frequency crystal oscillator...
I am working on nrf52832 BLE. I have used soft device s132. Antenna device is as per the reference design of NRF52832 and have used 32MHZ crystal for HFXO oscillator. but...
I am starting analysis for project of BLE Central device that is only receive broadcasting packet (advertise) from peripherals.
However, it’s unclear to me. I doubt will...
I notice that the sensitivity for the nRF52832 is defined as being ~2dB better in BLE mode than in NRF mode. I have also tested this to be correct.
However, I wonder - is...
Hi!
We have several products which use SoftDevice S110, some of them are already in production and are listed as Bluetooth Qualified, some of them we are preparing for production...
I've a custom board that uses a nrf52832 and Li-SOCl2 battery (3.7V). We've programmed several boards with our firmware and kept then with BLE advertisings every 300ms. A...
I am trying to develop a simple SPI master for a custom nRF52832 uC, but I can't find anny sort of sample codes that don't use Soft devices for this task. I need the code...
hi guys. I am currently using nrf52832 MDBT42Q Series from Raytac. I would like to know that how can I flash the softdevice and my application into the nrf52. My NRFgo unable...
I am currently doing some stress testing to ensure that I am correctly removing peers when the peer manager storage is full.
In this regard, my device is acting as a peripheral...
Hi,
I am developing application using nRF52832, s132, sdk13.2 which is collect sensor data and sent it to server. I have sent data to server using nRf52832 and interface...
Hello,
I'm trying to load BLE UART example on a custom module with nrf52832. I'm using SDK 14.
On the EVK it runs successfully, and I have the following addresses map...
Hello!
I'm trying to perform DFU over BLE using a NRF52 devkit. I'm getting the following error preceded by lots of "Invalid advertising data type" logs:
Traceback (most...
[SOLVED] turn off logging through UART.
Hello
I'm experiencing a strange issue where my device sends a beacon under DEBUG, but does not under RUN.
Due to that I tried...
Hi NordicSemiconductor Community,
I have a problem with the SEGGER Embedded Studio IDE, i want to build my project but i have the following error :
can't open 'C:/Users...
