Good afternoon! As the NRF7002 takes about 400ms to start up from shutdown, we would like to use the very low power deep sleep function for quick startup. Unfortunately, due...
Hi,
I would like to know the difference between the nRF52840-QIAA & nRF52840-QIAA -R7.
What is the significance of R7 here. Not able to find it in any conclusion ...
Hi, I'm working with the DWM3001CDK (nRF52833 + DW3110) and currently using SPI to interface with the DW3110 for UWB communication.
I'm trying to use a second UART to communicate...
Hi I am developing in 54L15. Now use DPPI to link
TIMER10's PUBLISH_COMPARE[3] ---> RADIO SUBSCRIBE_STOP,
it works fine.
Now I want to trigger a GPIO signal through...
Hello,
I´m trying to measure the current consumption on the nRF54L15-DK Rev. 0.9.2.
There are a few questions:
1) What is the role / purpose of the voltage buffer? ...
Hello, I have an issue regarding the current measurement of my nRF7002DK_nRF5340. I am trying to measure the current consumed during the transmission of a carrier on a Wi...
Post:
Hi Nordic Team,
We are currently developing a product based on the Raytac MDBT50Q-1MV2 module, which integrates the nRF52840 SoC. Our firmware is built using the...
Hi,
there were some significant changes to app_timer in sdk13.
I cannot use now the PRESCALER e.g. to 255 in order to configure the clock in such way to be able to tirgger...
Which case i have to use nrf_esb_suspend function instead of nrf_esb_disable/enable?
What function i have to use when i change radio RX to TX mode, changing radio channel...
What will be the operating voltage for nRF52 flash memory when using with CR2025 battery? I want to read/write data flawlessly in flash using CR2025 battery.
Hi,
I think I've found reliable way to cause hardfault when executing nrf_log_frontend-dequeue() and most likely cause nrf_log modules to write outside of allocated buffer...
Hi
Is there an example in the SDK or anywhere that displays the use of LE Advert Extensions? I have been browsing softdevice v6.0.0-6.alpha and I came across the structure...
Hi all !!!
I understand Output OOB, Input OOB.
I case of No OOB, value which is attached to Confirmation value is 0x00, what happens in case of static OOB?
Hi there~~ I'm trying to create a voice streaming application with the Mesh and the Nordic Thingy:52 I downloaded both the nRF5 SDK 14.2 & Mesk v1.0 to test the Mesh's light_switch...
Hi everyone,
Currently, my team is developing a BLE keyboard which uses 6KRO protocol. Are there any examples for the 6KRO protocol using nRF52 chips?
Thanks!
Update:
Hi again to everyone!
After a while, I've received a new custom board and a new cable to connect through P19. But everything are not working again.
Now, in...
I have a 12 MHz voltage controlled oscillator driving the nRF9E5 at pin xc1 and xc2 is open will this pose a problem for running the nRF9E5? The clock has a +-50ppm stability...
I am working on a project that requires me to wirelessly communicate with and program a left hand Oculus Touch controller, since dismantling it will cause damage. The controller...
I see I have more than 100 free pages (~ 101 KB) on Nrf51822 with SD130 but how can I assign all of them to the FDS module. I am going to manage a database with FDS on the...
Hello,
I am trying to use PCA10000 dongle with the pb-ble-driver-py libraries with absolutely no success, as I get a "Failed to open. Error code: 13" error.
I am running...
