Solved: Well, turns out delay and SCK doesnt work well together haha. I imagined the sck signal to be a background thread of some sort. I was wrong.
Hi guys,
at the...
Hi
Im looking for a developer in Denmark to discuss ble technology with. Im trying to get better to understand the technology, because i have some ideas involving beacons...
This system does not work if I enable the third Pipe (Pipe2) .
The system is working without any problem as one RX and two TX (Pipe0 and Pipe1).
The problem on enabling...
Hello,
i have read if not all posts about writing to FLASH while using BLE. But could not find the desirable method.
What i would like to do is to write to flash from...
Hello,
i have read all posts about writing to FLASH when using BLE. But could not find the desirable method.
What i would like to do is to write to flash from characteristic...
I'm trying to add the product key it shows an error "can not the product to your list" and therefore i will not able to access to the User guide
Thank you
hello, im from india im using nrf24l01+ for my project to transmit and receive data between two arduinos. i tried all tutorial basic programs but i cant sucessfully send and...
Hi, I purchased a Sparkfun Breakout board for the NRF52832, but the bootloader on it seems to be extremely unstable. Hence, I've decided to flash the NRF52832 directly from...
Hello,
I already checked below link, but want to clarify the limitations of how many concurrent sessions are allowed in Soft Device initialize.
devzone.nordicsemi.com...
Hello,
i add a new custom service with one characteristic that allows me to send values over BLE with nRF connect, but i must send some acceptable values (-2, -4, 0, 4, 10...
Using SDK14.0.0, nRF52832, GCC, GDB/Ozone, secure DFU
This question seems to get close to asking about my problem.
I am trying to debug my application with a loaded...
Hi,
We made a custom PCB using the NRF52832 and followed the reference design. While everything else is working in our system, the BLE part is not working. We are using...
Hello,
I try to develop an application on a nRF51802 device. But this device is not managed in nRF_Drivers.4.0.0-2.alpha.pack from Keil software.
Is there an update...
Hey guys! Like the title says, I'm looking for the best way to send values like humidity and VOC from the Nordic Thingy to the cloud. I have already set up the thingy to send...
Does anyone know of an off-the-shelf hardware and software that will let me read and write nRF52832 devices that are using the NFC Type 4 Library? We've tried the ACS ACR1252...
Materials publicly available say the chip works from 3.1 volts.
But is this the absolute minimum voltage or will it be possible to use also LiFePO4 battery cells with the...
I'm trying to set PWR_UP bit to 1 for the device to go into standby-I mode using STM32F103RBT6 and HAL libraries.
I send (0x20 | 0x00) command (write_reg | config reg)...
I'm trying to compile the S332 example project ble_ant_app_hrm_pca10040_s332.uvprojx. I'm using the V12 SDK and Keil uVision V5. When I try to compile I get an error saying...
Starting with "Development with GCC and Eclipse", I've gotten "blinky" to run on my BLE400 with an nrf58122 using Eclipse Oxygen. I think I'm using SDK12.3 . I started with...
pca10040 S132 5.1.0
if i run only a single nrf nus service (rx and tx) at 4 k bytes / sec both directions, how much load would this put on the 52832
the test is assuming...
Hi,
I'm connecting two I2C modules : MAX30102 and MPU-9250
I can individually communicate with either of these modules and they work okay. But if I connect both of them...
