I am using SDK_11 s130 on nrf51-dk. When err_code is any value other than NRF_SUCCESS, APP_ERROR_CHECK(err_code) will cause nRF51-dk board to reset. How can one get APP_ERROR_CHECK...
Hello All,
I have problem with ble_app_uart which are not support DFU services.
When I am implement both services device will not advertise. and when ble_nus uninitialized...
[symptom]
I want to update my application/bootloader/softdevice by DFU.
Steps are shown below.
bootloder/softdevice update
if 1 step is done, application update...
Dear Developer Zone,
I am new to ANT and am looking for someone to help me to setup an example 15 channel (14 devices) ANT network using the S332 soft-device to test communication...
Hello,
i am working with the Enhanced ShockBurst proprietary protocol and i am wondering where I can find the sources of this protocol, so that I can do some changes. ...
[uart - Copy.rar](/a master _error.png ttachment/3cc01f5e2484d2b0f33e62befd3e6a62)
hello there
I am interfacing master nrf51 dk with nxp's slave lpc11u24
(1) my main...
It is good practice to prefix the includes from one's C libraries with a directory so that they are all part of the same 'include namespace'. Unfortunately the Nordic SDK...
Hi,
I am trying to add the SAADC to an existing project. SDK 14.2 - Softdevice.
I quickly changed the existing code as follows:
Unfortunately, the callback gets...
Hi.
I am using the nRF52840 DK board and have integrated the SDK15 ESB_Rx example with the HID example.
The nRF52840 DK board has two USB ports. (J2, J3)
J2: Firmware...
Trying to track down an issue with IOS disconnecting shortly after connection when using NRF Connect, LightBlue doesn't connect at all.
We have a few GATT chars with...
Hello,
I am facing an issue when trying to use the example flash_fstorage_example in SDK15 with the softdevice. According to the documentation, using the reading and write...
I am testing SPIS to transmit mass of data(255 bytes each call) from nrf5 DK.
I found SPIS data shifting randomly.
The testing data is 0x88 but sometimes can get 0x44...
Datasheet of the Sensor:
www.ctconline.com/.../1_VS_TA102_DS.pdf
Accelerometer Out = 100mV/g =equivalent to=> +/- 8Vpk-pk
Temperature Out = 10mV/°C
Please provide...
FDS uses softdevice API. SDK 14.0.0
FDS writes are all successful for the same file id and different record keys until the flash is full
fds_delete_record() is called...
Hi,
I'm developing software for the nrf52832. However, I can't use the SDK of Nordic for several reasons.
In the code, I would like to save a small amount of data...
I tried to assigned each device to different group(subscriptions) by the following code segment.
for (uint16_t i=0; i < devCnt; i++) {
......
ERROR_CHECK(config_client_server_set...
Hello Everyone,
I am trying to incorporate NFC-BLE pairing feature in my ble_app_uart example. I have imported all the necessary files to the project and have installed...
Hi,
I am working on the project as a MultiLink example. My environment is using nRF52840DK & Softdevice 6 & SDK15.
I am trying to make multiple connections and communicate...
Trying to understand how the Device UUID is derived.
in iOS, Device UUID: FC7C7422-2BCF-894B-E848-855791DD3DD9
in RTT:
DEVICEID0: 0E064007 DEVICEID1: 14669F75 DEVICEADDR0...
Hello.
Hello.
I am trying to install pc-ble-driver-js on my computer but it fails to install. If anyone could guide me how to install it, that will be appreciated...
I'm having a strange problem where the Supervision timeout does not seem to work right at the point the connection is initiated (sd_ble_gap_connect() was called but BLE_GAP_EVT_CONNECTED...
I'm using the SPI in slave mode and have a very high power draw: > 2 mA. The issue happens both in my application + custom board as well as with the dev-kit + SPIS example...
