hello, Nrf24LU (Rx) , nRF51822(Tx).
The Nrf24LU Can only receive one packet。
if I use this function twice ， like this：
The Nrf24LU can receive Continuous.
I guess The...
Hi,
I use SDK v10, S110 v8 and dfu_dual_bank_ble_s100_pca10028. My application has dfu support.
I reset to bootloader from application after writing 0x0104 to dfu control...
I have a nRF51822 device.
When the connection interval is 50ms.
The transmission distance can up to 50m+.
But, when the connection interval is 1000ms.
The transmission...
Hi,
I have a simple question. It is possible to use the ble-sniffer nrf51822 on Kali Linux? I found a guide to use it on linux but I don't know if it is the same for Kali...
I've modified Nordic's "Nordic_Keyboard" sample to work with my custom board, just simple modifications to use custom_board.h rather than the default PC10028 configuration...
Hi,
I use HID application with S110 v8.0 profil.
I use BLE HID Keyboard example.
I put datas from smartphone to BOOT KEYBOARD OUTPUT REPORT and I whant read them by...
Hi all,
I use nRF51822 module and my environment is Eclipse + GCC + SDK 10.0. I refer to the example in path <SDK_PATH>/examples/ble_peripheral/ble_app_template, then make...
I am currently doing some stress testing to ensure that I am correctly removing peers when the peer manager storage is full.
In this regard, my device is acting as a peripheral...
Hi,
I am developing application using nRF52832, s132, sdk13.2 which is collect sensor data and sent it to server. I have sent data to server using nRf52832 and interface...
Hello,
I'm trying to load BLE UART example on a custom module with nrf52832. I'm using SDK 14.
On the EVK it runs successfully, and I have the following addresses map...
Hello!
I'm trying to perform DFU over BLE using a NRF52 devkit. I'm getting the following error preceded by lots of "Invalid advertising data type" logs:
Traceback (most...
[SOLVED] turn off logging through UART.
Hello
I'm experiencing a strange issue where my device sends a beacon under DEBUG, but does not under RUN.
Due to that I tried...
Hi NordicSemiconductor Community,
I have a problem with the SEGGER Embedded Studio IDE, i want to build my project but i have the following error :
can't open 'C:/Users...
Hello,
I am trying to send out a notification and getting this error code 13313 (in decimal, 0x3401 in hex). Which eventually leads to BLE_ERROR_GATTS_SYS_ATTR_MISSING...
I developing applciation based on nrf51822, sdk11. I have read several posts about using app_timer_cnt_get() and get only 0 value. As far as I understand, this is because...
i want to connect my nfr51822 device to only one phone( that means which phone was connected first). For this purpose i enable whitelists but i create whitelists nothing has...
In timer example in sdk 11, I replace the Timer 0 by timer 1 and timer 2 but the LED did not blink. Can you guys please guide me through this? In nrf_drv_config.h I have already...
I have Keil uVision-5 and loaded the legacy patch. However Nordic NRF51 does not appear anywhere as an option. The Project loads fine and compiles. However, I cannot use the...
nRF52862, SDK 14.2, SD 5.1.0,, Arm GCC (Eclipse)
I have a custom service that is working well when 1 device (phone) is connected. All notifications are sent properly to...
Hello everyone,
I am trying to add new service into ble_app_uart example. I compile successfully. I do not get an error. But the device is not advertising. I can only advertise...
