Hello. I am literally looking at the set_hrm_cccd function in Python used to write data. This is for the S130 heart rate collector example. I understand the sd.ble_gattc_write...
Totally new to Python but managed to get things like pyserial setup and I've been able run the ble sniffer. However that is as far as my Python knowledge extends, so I need...
pstorage_load and pstorage_clear appear to work fine, but whenever I do a pstorage_store the callback function is never called. This happens whether or not the Bluetooth unit...
Our USB keyboard using nrf24lu1p does not work on Mac OS 10.11.
Before Mac OS 10.11, USB keyboard was worked, but on Mac OS 10.11, it does not work.
I think your library...
In my design I need the RX to be standalone , I.E. no controller attached to it , does the programming STORE in the Chip ? If I set it up as a RX and set a specific Ch. Freq...
[Dev Env]
nRF51 DK
IoT SDK 0.8
IoT SoftDevice
[Question]
how i change my ip in ipv6_coap_server example use ipv6_address_set / ipv6_address_remove API.
To...
My application needs to be notified of large current draws due to the activity of the nRF8001. The active signal works fine for this purpose, but why is it available only...
What is the typical expected receiver sensitivity when performing BER test (1Msps, 16 byte packets) of the radio module ? The spec refers to 2 values: -93 and -96 dBm (p.231...
Hello,
We are considering merging the Eddystone and iBeacon features together, packet types toggling at each interval tick, then we assumed that we should take the Eddystone...
My device is sending a beacon under DEBUG, but not under RUN.
The issue started when I converted the scan_and_forward example to use a 16-bit device address.
It steps...
Dear Sir or Madam,
I'm using a dev kit with the nRF52832 to realize a project in school. So my work contains two wearables and both include the nRF52832. Now I want to communicate...
Hello,
is it somehow possible to calculate the distance of a BLE enabled and advertising periodially cell phone to a turnstyle gate.
There are for example 10 turnstyle...
Hello,
I'm trying to update from Mesh SDK 1.0.0 to 1.0.1, I've followed http://infocenter.nordicsemi.com/topic/com.nordic.infocenter.meshsdk.v1.0.1/md_doc_getting_started_how_to_nordicSDK...
Hi all,
I would like someone give me a suggestion about timers.
in my current approvement I am using an RTC timer with 32k crystal to control my sleep times it is power...
Hi there,
I have an nRFready Smart Remote 3 in front of me to evaluate for development of an upcoming product. I've had a look around the forums and documentation, but...
I’m currently making some measurements with a power analyzer on both, our own hardware design with the nRF52840 (Samples B) and the nRF52840 Preview Dev Kit.
I took the...
Hello Community,
this is my first question, since I could not find any clue on the internet and here on the devzone.
Problem:
I need to read/write a value to a GATT...
Hi,
I compiled (using ARM GNU) and run the USB CDC ACM example found on SDK_14_0_0. I have windows 10.
Windows 10 do not reckognize it as a CDC device and instead I...
hi,
I am developing with nRF 52832 on my own board. the code worked fine until I added the UART_init() function. my source code outputs an error message.
i reinstalled...
Hello,
How reset device from code to take effect of enabling access port protection? NVIC_SystemReset() doesn't work. I can read flash using j-link.
Device: nRF52832
