Suppose a nRF9E5 transmitter is set for continuous transmission on a channel.
A nRF9E5 receiver listening on that channel:
finds carrier and sets CD
finds address...
I will be deploying my nRF51822-powered devices into the field and the end user will not be able to have any physical access to, for example, power cycle the board. I need...
Hi,
We are using the ble_app_uart example in evaluation board to read data from some sensors and send it to the nRF UART V2.0 in Android 4.4. Every 20 ms I am trying to...
I am try this at nrf51_sdk_v6_0_0_43681\nrf51822\Board\nrf6310\s110\ble_app_hids_keyboard
Firt I connect to Android device and keep one whitelist.pp_addrs and one whitelist...
Hi,
Parameter uint8_t ble_gap_scan_params_t::filter is present in the documentation, but not implemented.
Checked for SDK 5.2.0 and 6.0.0.
devzone.nordicsemi.com...
After I get a Disconnected() event, I want to start scanning again, therefore try to call StartDeviceDiscovery() again.
IsDeviceDiscoveryOngoing was checked before.
The...
Hello!
I am developing a FreeRTOS application for nrf52832 with S132 Soft device
Recently I ran out of ram and checked the map-file for clues. The large posts in the mapfile...
Hi,
I don't understand why the characteristic FitnessMachine Feature : (0x2ACC) is not decoded as a bit field by nRF Connect
I can read it and i can see the good value...
using nRF51-DK
I'm a noob and currently trying to implement a custom service by modifying the 'Heart Rate Service' example which inclued the 'BAS' which is battery status...
Hello All,
I am working on the NRF52810 board with 15.3 sdk in segger IDE.
I have implemented fds with 2 key with 1 file id to store data.
I am storing 2 - 3 1 byte...
Hi, I'm working on building an embedded computer with Bluetooth capabitilites. I am aware of the various WiFi/Bluetooth chips, but my application does not need WiFi, only...
Hi,
We are developing the cycle power services and facing the issues in using the control point characteristic. I am able to connect and observe all the characteristics...
Hi,
we are using MQTT to push the sensor and GPS data with 1 hour interval. After 4 consecutive connect and disconnect, MQTT is returning socket error. It requires the device...
Hi,
I am using NRF51822 SDK12; S130 and trying to qualify Batter level service with the SIG's PTS device (dongle)
So far encountered a problem with Test Case: BAS/SR/DES...
Just got a nRF5340 DK, testing on macOS 10.15.2. Setup was smooth – the nRF Connect assistant is pretty good. The only feedback would be that an explanation of the "Variables...
Hello Nordic Team,
I'm currently working on a project based on the nRFready desktop. My application requires using the pipes 0-2: pipes 0 and 1 are used in conjunction with...
Hello everyone!
I want to use the app_sdcard to read/write with fatfs on a uSD card in my app which is based on FreeRTOS. While i was implementing this library, i saw that...
Hi,
I would like to know, where the packets are written into the flash for the mesh DFU example.
In nrf_mesh_dfu.c is a function nrf_mesh_dfu_cmd_send:
It calls...
Hello,
I have a little issue during the mesh configuration of my network.
First my provisioner (called master) provision and configure a first node (called slave), this...
I have downloaded project from https://devzone.nordicsemi.com/f/nordic-q-a/55710/while-building-thingysdkv210-on-segger-showing-error-thingysdkv210-source-modules-thingee_ble_handler...
